Exam Center · Traps

Exam Traps and the Questions People Miss

Most CCNA marks are lost not on hard topics but on near-miss concepts where the tempting answer is almost right. This page collects the classic traps, gives the wrong-but-tempting answer for each, and explains the reasoning that makes the correct answer correct. Read it twice before exam day.

CCNA 200-301 v1.1 14 traps 10-question self-check Verified 2026-10-11

Each trap below follows the same shape: the tempting answer that draws people in, then the correct reasoning. If you can explain why the tempting answer is wrong, you will not fall for it on the exam.

1. Switch vs router

Tempting answer “A switch can connect two different subnets, because a Layer 3 switch has an IP address.”

The trap is conflating a Layer 2 switch with a Layer 3 (multilayer) switch. A plain Layer 2 switch forwards frames using MAC addresses and stays inside one subnet. A router — or an explicitly configured Layer 3 switch acting as a router — forwards packets between subnets using IP addresses. On the exam, if two different networks must communicate and the answer list includes both a Layer 2 switch and a router, the router is correct.

2. PDU names

Tempting answer “Everything is a packet.”

Each layer has its own protocol data unit name. Bits at Physical, frame at Data Link, packet at Network, and segment (TCP) or datagram (UDP) at Transport. A question asking for the Layer 4 unit of UDP expects datagram, not packet, and a question about Ethernet expects frame. Precision is the whole point of the trap.

3. Administrative distance

Tempting answer “The router installs both routes and load-balances between them.”

When the same prefix is learned from different sources, the router compares administrative distance first and installs only the best one. Connected is 0, static is 1, EIGRP 90, OSPF 110, RIP 120. So a static route beats an OSPF route to the same prefix. Load-balancing happens only between routes from the same protocol with equal metrics.

4. Longest-prefix match

Tempting answer “The router uses the route with the lowest administrative distance.”

Administrative distance only breaks ties between routes to the same prefix. When several routes match a packet, the router chooses the one with the longest prefix first. For a packet to 10.1.1.5, a /24 route beats a /16 route every time, even if the /16 came from a more trusted source. Order of operations: longest match, then administrative distance, then metric.

5. Standard ACL placement

Tempting answer “Put every ACL as close to the source as possible.”

A standard ACL matches only the source address, so placing it near the source of the traffic you intend to filter may also block unrelated traffic from that same source to other destinations. Standard ACLs belong near the destination. Extended ACLs, which match source, destination, and ports, belong near the source so unwanted traffic is dropped early.

6. Native VLAN mismatch

Tempting answer “A native VLAN mismatch just creates an STP loop.”

A native VLAN mismatch is not an STP problem. If the two ends of an 802.1Q trunk disagree on the native VLAN, untagged frames from one side's native VLAN are placed into the other side's native VLAN — traffic leaks between VLANs, and CDP logs a mismatch. It is a segmentation and security fault, and the fix is to make the native VLAN identical on both ends.

7. Duplex vs speed mismatch

Tempting answer “One end at 1000 Mbps and the other at 100 Mbps is a duplex mismatch.”

Different rates are a speed mismatch. A duplex mismatch is when both ends agree on the same speed but disagree on duplex — commonly one side hard-set to full duplex and the other auto-negotiating to half. The signature of a duplex mismatch is late collisions and runts with the link still up, whereas a speed mismatch usually keeps the link down or badly degraded.

8. Default vs static route

Tempting answer “A host with no route for a destination just sends the packet to its default gateway.”

The host does, but the question is usually about the router. A router forwards an unmatched destination only if it has a default route (0.0.0.0/0), which is a specific case of a static route and appears as the gateway of last resort. Without a default route, a router drops the packet and returns ICMP unreachable. A static route to exactly that destination would also work, but a default route is the catch-all.

9. PAT terminology

Tempting answer “NAT and PAT are the same thing.”

PAT (Port Address Translation), also called NAT overload, is a type of NAT. Plain dynamic NAT maps inside addresses to a pool of public addresses, one-to-one at a time. PAT instead lets many inside hosts share a single public address by tracking unique source ports. The key exam phrase is “many to one” or the keyword overload in the command.

10. STP roles and states

Tempting answer “A blocking port forwards frames but is just slower.”

Roles and states are different things. Roles are root, designated, and alternate (or backup). States are blocking, listening, learning, and forwarding. A port in the blocking state does not forward frames — it only receives BPDUs and stays ready to take over. The forwarding state forwards, and the learning state builds the MAC table without forwarding yet.

11. OSPF DR/BDR

Tempting answer “The DR is the router with the highest IP address.”

DR/BDR election uses the highest OSPF interface priority first, and only then the highest router ID to break a tie. The default priority is 1, and a priority of 0 makes a router ineligible. Also remember that DR/BDR are elected only on broadcast and non-broadcast multi-access networks; on a point-to-point link there is no election at all.

12. WPA2 vs WPA3

Tempting answer “WPA2 uses SAE and WPA3 uses AES-CCMP.”

It is the other way round. WPA2 uses AES with CCMP and a four-way handshake. WPA3 introduces SAE (Simultaneous Authentication of Equals), which resists offline dictionary attacks against the pre-shared key. WEP (RC4) and WPA (TKIP) are legacy and insecure.

13. JSON vs XML

Tempting answer “JSON uses tags just like XML.”

JSON uses braces for objects and brackets for arrays, with data as key-value pairs: {"name":"R1"}. XML uses opening and closing tags: <name>R1</name>. YAML is the third format, using indentation and no brackets. The exam frequently shows a data sample and asks which format it is.

14. Control plane vs data plane

Tempting answer “The control plane forwards the actual user packets.”

The control plane builds the forwarding information — it runs routing protocols and populates tables. The data plane (forwarding plane) actually moves the packets using that information. SDN centralises the control plane in a controller and leaves the data plane on the devices, which is the separation the blueprint asks you to describe.

Check yourself

Ten of the traps above, turned into questions. Pick the single best answer; feedback is immediate.

Exam traps — 10 questions
  1. A frame from PC-A arrives at a router and must be forwarded to a host on another subnet. What changes at the router?

    • Only the source IP address
    • The Layer 2 source and destination MAC addresses
    • Only the destination port number
    • Nothing; the frame is forwarded unchanged

    The IP addresses stay end to end, but the router strips the old frame and builds a new one with its own MAC as source and the next hop's MAC as destination.

  2. Which PDU name is correct at the Network layer?

    • Frame
    • Packet
    • Segment
    • Datagram

    Layer 3 produces packets. Frames are Layer 2, and segments and datagrams are Layer 4 (TCP and UDP respectively).

  3. A router holds a static route and an OSPF route to the same prefix. Which is installed?

    • The OSPF route
    • The static route
    • Both, equally
    • Neither until metrics are compared

    Administrative distance is compared first: static is 1 and OSPF is 110. The static route wins outright for that prefix.

  4. A router has 10.0.0.0/8 and 10.1.1.0/24 in its table and must forward to 10.1.1.5. Which route is used?

    • 10.0.0.0/8
    • 10.1.1.0/24
    • Both, load-balanced
    • Neither

    Longest-prefix match wins: the /24 is the more specific match for 10.1.1.5 and is preferred regardless of source.

  5. Where is a standard ACL best placed?

    • As close to the source as possible
    • As close to the destination as possible
    • On the local loopback interface
    • On every router in the path

    Because a standard ACL filters on source alone, placing it near the destination avoids blocking that source's traffic to unrelated destinations.

  6. Two ends of an 802.1Q trunk are configured with different native VLANs. What is the result?

    • A Spanning Tree loop
    • Traffic leakage between VLANs
    • A speed mismatch
    • No effect at all

    Untagged frames on one side's native VLAN are placed into the other side's native VLAN, leaking traffic between VLANs. CDP also reports the mismatch.

  7. One end of a link is set to 1000 Mbps full duplex and the other to 1000 Mbps half duplex. What is this?

    • A speed mismatch
    • A duplex mismatch
    • A cable fault
    • Normal operation

    Both ends agree on speed but not duplex, so this is a duplex mismatch — it shows late collisions and runts while the link stays up.

  8. A router receives a packet whose destination is in no specific route it holds. What does it do if it has a default route?

    • Drops the packet immediately
    • Forwards it using the default route
    • Broadcasts it to all interfaces
    • Returns it to the sender

    The default route 0.0.0.0/0 is the gateway of last resort and matches anything without a more specific route. Without it, the packet would be dropped.

  9. Which statement about PAT (NAT overload) is correct?

    • It maps one inside address permanently to one public address
    • It lets many inside hosts share one public address using unique source ports
    • It translates destination addresses only
    • It is identical to static NAT

    PAT multiplexes many inside sessions onto one public address by tracking source ports. Permanent one-to-one mapping is static NAT.

  10. Which STP state forwards frames?

    • Blocking
    • Forwarding
    • Learning
    • Listening

    Only the forwarding state passes frames. Learning builds the MAC table but does not forward; blocking and listening do not forward either.

Sources & references

  1. Cisco. CCNA Exam v1.1 (200-301) Exam Topics. learningcontent.cisco.com.
  2. Moy, J. RFC 2328: OSPF Version 2 (1998). rfc-editor.org/rfc/rfc2328.
  3. IEEE. IEEE 802.1Q — Bridges and Bridged Networks. standards.ieee.org.
  4. Sriram, K. & Montgomery, D. RFC 3376: Internet Group Management Protocol, Version 3 (2002). rfc-editor.org/rfc/rfc3376.
  5. IEEE. IEEE 802.11 — Wireless LAN MAC and PHY Specifications. standards.ieee.org.

Target exams: CCNA 200-301 v1.1 · CyberOps Associate 200-201. Last content verification: 2026-10-11.