CCNA Flashcards
Eighty-plus click-to-reveal cards grouped by exam domain. Read the prompt, recall the answer, then open the card to check. Cover the answer first — active recall beats rereading every time.
How to study with these
Work in short bursts. For each card, say the answer aloud before you open it. Mark the ones
you miss and revisit only those the next day — spaced repetition is far more effective
than rereading the whole set.
Smart revision
Study session
Domain 1.0 — Network Fundamentals
Network
Two or more devices connected by a medium so they can share data and resources using common protocols.
Host (end device)
A device that is a source or destination of traffic (PC, phone, server, printer) and has a network address.
Intermediary device
A device that forwards traffic between hosts rather than originating it: switch, router, access point, firewall.
Switch vs router
A switch forwards frames within one LAN using MAC addresses; a router forwards packets between different networks using IP addresses.
Interfaces and ports: console vs SVI
The console port is out-of-band management; the switch virtual interface (SVI) is an in-band management IP on a VLAN.
Three-tier campus design
Access (connects end devices), Distribution (policy and routing between access and core), Core (high-speed backbone).
Collapsed core
A two-tier design that merges the distribution and core layers in smaller campuses.
Star / full mesh / hub-and-spoke topologies
Star: all devices to one central point. Full mesh: every device to every other (max redundancy, high cost). Hub-and-spoke: branches connect only to a central site.
LAN vs WAN
A LAN is local, usually organisation-owned with high bandwidth per port; a WAN spans large areas and is typically leased from a service provider.
TCP vs UDP
TCP is connection-oriented and reliable (handshake, acknowledgements, retransmission). UDP is connectionless, best-effort, and low overhead.
Socket
The combination of an IP address and a transport-layer port number, uniquely identifying an application endpoint (for example 10.0.0.1:443).
PDU names by layer
Transport: segment (TCP) or datagram (UDP). Network: packet. Data Link: frame. Physical: bits.
Fibre vs copper
Fibre carries light over long distances (single-mode farthest, multimode shorter); copper (Cat 5e/6) is limited to about 100 m.
Power over Ethernet (PoE)
Delivers DC power and data over the same twisted-pair cable to devices such as IP phones, cameras, and access points.
Speed/duplex mismatch symptom
The link stays up but throughput is poor and error counters climb; a classic interface issue at Layer 1.
2.4 GHz non-overlapping channels
Channels 1, 6, and 11 in North America. The band is crowded and causes co-channel interference.
RFC 1918 private ranges
10.0.0.0/8, 172.16.0.0/12, 192.168.0.0/16. Not routable on the public Internet.
APIPA range
169.254.0.0/16, self-assigned when a host cannot reach a DHCP server.
Usable hosts formula
2h − 2, where h is the number of host bits. The subtraction removes the network and broadcast addresses.
IPv6 address size and notation
128 bits, written as eight groups of four hex digits, with leading zeros removed and one run of zero groups replaced by "::".
IPv6 address types
Global unicast 2000::/3; link-local FE80::/10; unique local FC00::/7; multicast FF00::/8; plus anycast. No broadcast.
IPv6 EUI-64 and SLAAC
EUI-64 builds a 64-bit interface ID from the MAC; SLAAC lets a host form an address from a router advertisement plus NDP.
Domain 2.0 — Network Access
VLAN definition
A logical broadcast domain on a switch. Separating a switch into VLANs splits broadcast domains and improves security.
802.1Q tag size and content
4 bytes: a 2-byte TPID (0x8100) and a 2-byte field holding a 12-bit VLAN ID and priority bits.
Default VLAN, native VLAN
The default VLAN is VLAN 1. The native VLAN carries untagged frames on a trunk and also defaults to VLAN 1.
Normal vs extended VLAN range
Normal range 1–1005; extended range 1006–4094. VLANs 1002–1005 are reserved for legacy media.
Access port vs trunk port
An access port belongs to one data VLAN and sends untagged frames to a host; a trunk carries multiple VLANs with 802.1Q tags.
Voice VLAN
A separate VLAN carrying tagged IP-phone traffic so it can be prioritised, while the attached PC's data stays on the access VLAN.
DTP
Dynamic Trunking Protocol negotiates whether a Cisco link becomes a trunk. Best practice is to hard-set trunk/access and disable DTP with nonegotiate.
CDP vs LLDP
CDP is Cisco proprietary; LLDP is the open IEEE 802.1AB standard. Both discover directly connected neighbours and their capabilities.
EtherChannel
Bundles up to eight physical links into one logical link for more bandwidth and redundancy; STP sees one link, avoiding blocks.
LACP vs PAgP
LACP is the IEEE 802.3ad standard; PAgP is Cisco proprietary. LACP modes are active/passive; PAgP modes are desirable/auto.
STP purpose and root bridge
STP builds a loop-free Layer 2 topology by blocking redundant ports. The root bridge is the switch with the lowest bridge ID (priority then MAC).
Default STP timers
Hello 2 s, forward delay 15 s, max age 20 s. Default bridge priority 32768, in increments of 4096.
PortFast and BPDU guard
PortFast puts an access port straight into forwarding; BPDU guard err-disables the port if a BPDU arrives, blocking an unauthorised switch.
Rapid PVST+
Cisco's per-VLAN RSTP implementation and default STP mode, converging in seconds.
CAPWAP ports
UDP 5246 for control and UDP 5247 for data, used between lightweight APs and a wireless LAN controller.
AP modes
Local (tunnel to WLC), FlexConnect (local switching, survives WAN loss), Monitor (scan only), Sniffer (capture), Bridge, SE-connect.
WPA2 vs WPA3
WPA2 uses AES-CCMP; WPA3-Personal uses SAE (Dragonfly handshake) for stronger resistance to offline guessing. Enterprise uses 802.1X/EAP.
Port security
Limits which/how many MAC addresses may use a port. Violation modes: protect (drop silently), restrict (drop plus alert), shutdown (err-disable).
Domain 3.0 — IP Connectivity
Routing table codes
C connected, L local, S static, S* default, O OSPF, D EIGRP, R RIP.
Administrative distance values
Connected 0, static 1, EIGRP 90, OSPF 110, RIP 120. Lower is more trusted.
Longest-prefix match
When several routes match a destination, the router uses the one with the longest (most specific) prefix length.
Gateway of last resort
The default route (0.0.0.0/0) used when no more specific route matches.
Static route syntax
ip route NETWORK MASK NEXT-HOP, for example ip route 192.168.2.0 255.255.255.0 10.0.0.2.Floating static route
A static route with a higher administrative distance so it is used only if the preferred route fails (a backup).
OSPF multicast addresses
224.0.0.5 for all OSPF routers and 224.0.0.6 for the DR and BDR.
OSPF hello/dead timers
10 s hello and 40 s dead on broadcast and point-to-point networks. The dead interval is four times the hello by default.
OSPF metric
Cost = reference bandwidth / interface bandwidth, with a 100 Mbps reference by default (108 / BW).
OSPF router ID selection
Explicit router-id first, then the highest loopback IP, then the highest active interface IP.
OSPF DR/BDR purpose
On a multi-access network the DR and BDR reduce adjacencies: other routers form full adjacencies with the DR/BDR and stay in 2-WAY with each other.
OSPF EXSTART/EXCHANGE stuck cause
Usually an MTU mismatch on the link, which prevents database description agreement.
HSRP basics
First-hop redundancy giving hosts one virtual gateway. Default priority 100 (higher wins); virtual MAC 0000.0C07.ACxx.
VRRP
The open-standard first-hop redundancy protocol (RFC 5798); also default priority 100, higher wins. Uses virtual MAC 0000.5E00.01xx.
OSPF network statement wildcard
A wildcard mask inverts the subnet mask: /24 becomes 0.0.0.255.
Domain 4.0 — IP Services
NAT address roles
Inside local (private host on the inside), inside global (that host as seen outside), outside local, outside global.
PAT
NAT overload: many inside addresses share one or a few global addresses by using unique source port numbers.
PAT configuration line
ip nat inside source list 1 interface gi0/0 overload, with ip nat inside and ip nat outside on the interfaces.Static NAT vs port forwarding
Static NAT maps one inside address to one outside address; port forwarding (static PAT) maps an external port to one internal host and port.
DHCP DORA
Discover, Offer, Request, Acknowledge — the four-message DHCPv4 lease exchange.
DHCPv4 ports
UDP 67 for servers, UDP 68 for clients. DHCPv6 uses UDP 546 (client) and 547 (server).
DHCP relay / helper address
ip helper-address SERVER-IP converts a client broadcast into a unicast to a DHCP server on another subnet.DNS ports
UDP 53 for queries and TCP 53 for large responses and zone transfers.
TFTP port and use
UDP 69; used to copy configurations and IOS images to/from a server.
NTP port and stratum
UDP 123. Stratum 0 is the reference clock; 1 is directly attached; up to 15. Time matters for logs and certificates.
SNMP ports
UDP 161 for manager-to-agent queries/polls and UDP 162 for agent-to-manager traps.
Syslog severity levels
0 emergency, 1 alert, 2 critical, 3 error, 4 warning, 5 notification, 6 informational, 7 debugging. Lower is more severe.
SSH vs Telnet
SSH (TCP 22) encrypts the session; Telnet (TCP 23) is plaintext and should be disabled. SSH needs hostname, domain, RSA keys, and a local user.
DSCP EF
Expedited Forwarding, DSCP 46, is the recommended marking for voice traffic.
Shaping vs policing
Shaping buffers and delays excess traffic; policing drops or re-marks it immediately.
Domain 5.0 — Security Fundamentals
CIA triad
Confidentiality, Integrity, Availability — the three core security goals.
Vulnerability, threat, exploit
A vulnerability is a weakness; a threat could exploit it; an exploit is the tool or method; a countermeasure reduces the risk.
Principle of least privilege
Grant users and systems only the access required to do their job, limiting the impact of a compromise.
MFA
Multi-factor authentication combines factors from different categories: something you know, have, or are.
Enable secret vs enable password
enable secret stores a hash (strong); enable password is weak. Use service password-encryption for line passwords.TACACS+ vs RADIUS
TACACS+ is Cisco proprietary, TCP 49, encrypts the whole body, separates AAA. RADIUS is open, UDP 1812/1813, encrypts only the password.
Remote-access vs site-to-site VPN
Remote-access connects an individual client to the network; site-to-site connects two fixed gateways over an untrusted network.
IPsec vs GRE
IPsec provides encryption and integrity; GRE forms a tunnel and can carry multicast/routing protocols but is unencrypted alone.
Wildcard mask for one host
0.0.0.0 matches exactly one address; 255.255.255.255 matches any. The wildcard is the inverse of the subnet mask.
Standard vs extended ACL
Standard matches source only and is placed near the destination; extended matches source, destination, protocol, and ports and is placed near the source.
Implicit deny
Every ACL ends with an invisible deny any any, so at least one permit is needed.
ACL ranges
Standard 1–99 and 1300–1999; extended 100–199 and 2000–2699. Named ACLs avoid number ranges.
Port security violation modes
Protect (drop silently), Restrict (drop plus syslog/SNMP), Shutdown (err-disable the port).
DHCP snooping and DAI
DHCP snooping blocks rogue DHCP servers on untrusted ports; Dynamic ARP Inspection validates ARP against the snooping database to stop spoofing.
802.1X
Port-based network access control: a device is authenticated against a RADIUS server before the port is authorised, possibly into a VLAN.
BPDU guard / root guard
BPDU guard disables a PortFast access port that receives a BPDU; root guard prevents a port from becoming the root, protecting the topology.
Domain 6.0 — Automation & Programmability
The three planes
Management (admin/monitoring: SSH, SNMP, syslog), Control (path decisions: OSPF, STP), Data (forwarding actual traffic).
Northbound vs southbound API
Northbound connects applications/tools to the controller; southbound connects the controller to the network devices.
OpenFlow
A southbound SDN protocol that lets a controller install forwarding entries into devices.
REST characteristics
An architectural style: stateless, uses standard HTTP methods and URIs, commonly exchanges JSON.
CRUD to HTTP methods
Create=POST, Read=GET, Update=PUT/PATCH, Delete=DELETE.
HTTP status code families
2xx success (200 OK, 201 Created), 3xx redirect, 4xx client error (400, 401, 404), 5xx server error (500).
Ansible vs Puppet/Chef
Ansible is agentless (SSH, YAML playbooks); Puppet and Chef are agent-based (agents on managed nodes).
Idempotence
Running the same configuration job repeatedly yields the same result with no unintended extra changes.
JSON object vs array
An object is key/value pairs in { }; an array is an ordered list in [ ].
JSON vs XML vs YAML
JSON uses braces/brackets and quoted keys; XML uses tags; YAML uses indentation and key: value pairs.
DNA Center / Catalyst Center
Cisco's controller and management platform for intent-based networking, automated provisioning, and assurance, with a northbound REST API.
Intent-based networking
Expressing desired business outcomes as policy, translating them to device configuration, and continuously verifying compliance.
Sources & references
- Cisco. CCNA (200-301) Exam Topics, all domains. cisco.com.
- Rekhter, Y. et al. RFC 1918: Address Allocation for Private Internets (1996). rfc-editor.org/rfc/rfc1918.
- Hinden, R. & Deering, S. RFC 4291: IP Version 6 Addressing Architecture (2006). rfc-editor.org/rfc/rfc4291.
- Moy, J. RFC 2328: OSPF Version 2 (1998). rfc-editor.org/rfc/rfc2328.
- IEEE. IEEE 802.11 Wireless LAN Standards. standards.ieee.org.
Target exams: CCNA 200-301 v1.1 · CyberOps Associate 200-201. Last content verification: 2026-10-11.