Lab Workbook
Hands-on labs are where the exam's configuration and troubleshooting questions become muscle memory. Work through the ten labs below in order, or jump to the skill you need to practise.
Lab index
Each lab is a self-contained page with topology, objectives, a step-by-step task list, and verification commands. Open a lab in a new tab and work alongside it.
| # | Lab | Week / topic | Key skills | Where |
|---|---|---|---|---|
| 1 | Basic Router Configuration | Week 2 — Networking Today | Hostname, passwords, banner, interfaces, saving config | Packet Tracer |
| 2 | Static Routing | Week 3 — Protocols | IPv4 addressing, static and default routes, ping/traceroute |
Packet Tracer |
| 3 | VLANs, Trunks & Inter-VLAN Routing | Week 5 — Data Link Layer | VLAN creation, 802.1Q trunks, router-on-a-stick, SVIs | Packet Tracer |
| 4 | STP & EtherChannel | Week 5 — Data Link Layer | Root election, port roles, LACP/PAgP bundles, show etherchannel |
Packet Tracer |
| 5 | OSPF Single-Area | Week 6 — Network Layer | OSPF neighbours, network statements, DR/BDR, verification |
Packet Tracer |
| 6 | HSRP First-Hop Redundancy | Week 6 — Network Layer | Virtual IP, priority and preempt, active/standby failover | Packet Tracer |
| 7 | Wireless Configuration | Week 8 — Transport Layer | WLC, SSIDs, WPA2, DHCP integration, client association | Packet Tracer |
| 8 | NAT & PAT | Week 9 — Application Layer | Static and dynamic NAT, PAT overload, inside/outside interfaces | Packet Tracer |
| 9 | ACL Configuration | Week 10 — Security Fundamentals | Standard and extended ACLs, placement, show access-lists |
Packet Tracer |
| 10 | Layer 2 Security | Week 10 — Security Fundamentals | Port security, DHCP snooping, DAI, BPDU guard | Packet Tracer |
Note
The wireless lab (7) is grouped with the transport-layer week in the course calendar, so its
page lives under
week-08-transport-layer. Follow the links rather than guessing
the folder.
How to practise a lab
- Read the objectives first. Know what "done" looks like before you touch a CLI.
- Draw the topology. Sketch devices, interfaces, and addresses on paper; it fixes the addressing in memory.
- Configure from memory where you can. Peek at the steps only after an attempt; struggle produces recall.
- Verify at every layer. Check interface status, addressing, then reachability, then the feature itself.
- Break it on purpose. Shut a link, remove a route, or misconfigure a VLAN and watch how the failure appears.
- Save and compare. Use
show running-configandcopy running-config startup-config, then rebuild from scratch a second time.
! A three-command sanity sweep after any change
R1# show ip interface brief
R1# show ip route
R1# ping 192.168.10.1
Skills checklist
Tick a box only when you can do the task from memory and verify it without notes.
- Set a hostname, enable secret, and MOTD banner on a router or switch.
- Configure IPv4 and IPv6 addresses on physical interfaces and SVIs.
- Create VLANs, assign access ports, and build an 802.1Q trunk.
- Route between VLANs with router-on-a-stick or SVIs.
- Explain and predict STP root election, port roles, and states.
- Bundle links with LACP or PAgP and verify with
show etherchannel summary. - Configure a single-area OSPFv2 domain and confirm full adjacency.
- Configure HSRP and test failover by shutting the active router.
- Join a client to a WPA2 WLAN served by a WLC.
- Configure static NAT, dynamic NAT, and PAT overload.
- Write a standard and an extended ACL and place each correctly.
- Harden access ports with port security, DHCP snooping, DAI, and BPDU guard.
- Subnet a /24 into variable-length subnets for a given host requirement.
- Read a routing table and explain each route's code, metric, and next hop.
Common lab mistakes
- Forgetting
no shutdown— interfaces are administratively down by default. - Wrong subnet mask — the two ends of a link must be in the same subnet.
- Missing or wrong trunk — a VLAN that exists on both switches still cannot cross an access link.
- Native VLAN mismatch — mismatched native VLANs cause CDP errors and traffic leaks.
- OSPF interface left passive — a passive interface never forms an adjacency.
- ACL direction and placement — apply it inbound, near the source, and remember the implicit deny.
- NAT inside/outside reversed — interfaces must be marked
ip nat insideandip nat outsidecorrectly. - No final save —
write memorynever ran, so the config is lost on reload.
Sources & references
- Cisco. CCNA (200-301) Exam Topics, Configuration and Troubleshooting. cisco.com.
- Cisco. Cisco IOS Configuration Fundamentals Command Reference. cisco.com.
- Cisco. Cisco Networking Academy. netacad.com.
Target exams: CCNA 200-301 v1.1 · CyberOps Associate 200-201. Last content verification: 2026-10-11.