Week 1 · Lesson 3

Foundations of Connectivity

Before a host can talk to anything it must be reachable physically and configured logically. This lesson defines what connectivity really means at both levels, then explains how data rates, delay, and message types shape every conversation on a network.

CCNA 200-301 Domain 1.0 Network Fundamentals Verified 2026-10-11
Part 1

What connectivity means

Connectivity is the ability of one host to exchange data with another. It is not a single thing you can point at — it is the result of two independent layers working together:

Both must be correct. A PC with a cable plugged in but no IP address is physically connected yet logically isolated: its signal leaves the NIC, but nothing knows where to deliver it. Conversely, a perfectly configured PC with a cut cable cannot reach anything. Troubleshooting always starts by asking which kind of connectivity is broken.

Definition — connectivity. A state in which a host has both a functioning physical path to the network and a correct logical configuration, allowing it to exchange data with other hosts.
Connectivity checker · toggle the two layers
Part 2

Physical connectivity

Physical connectivity is built from three parts: the NIC, the media, and the connectors.

The network interface card (NIC) is the hardware that joins a host to the medium. It is usually built into the motherboard but can be an expansion card. The NIC holds the device's MAC address and converts data between the digital form used by the host and the signals used on the wire or in the air.

The media is the physical path the signals travel along. The three families are copper, fibre, and wireless:

MediumSignalTypical connectorNotes
Copper twisted pair (UTP/STP)ElectricalRJ-45 (8P8C)Low cost; Ethernet over twisted pair is limited to 100 m; susceptible to interference.
Fibre opticLightLC, SC, STLong distance, high bandwidth; immune to electromagnetic interference (EMI).
WirelessRadioAntennas (no cable)Mobility; affected by interference, distance, and obstacles.

Copper cable uses twisted pairs to reduce interference and is terminated with the familiar RJ-45 plug. Common categories are Cat 5e, Cat 6, and Cat 6a, which differ in the speeds they support. Fibre optic carries data as pulses of light: single-mode fibre supports the longest distances, while multimode fibre is used for shorter runs such as within a building or data centre. Wireless media use radio waves (the IEEE 802.11 family, known as Wi-Fi).

Remember. Copper twisted-pair Ethernet has a 100-metre channel limit. If a device is beyond that, you extend with fibre or an access point — not with a longer copper cable.
Part 3

Logical connectivity

Once the physical path exists, the host must be configured so traffic can actually be delivered. Four settings give a host everything it needs to communicate both locally and across the Internet:

  1. IP address — the host's logical, routable address on the network. It identifies the host to the rest of the internetwork.
  2. Subnet mask — tells the host which part of its IP address is the network portion and which is the host portion. It is how the host decides whether a destination is local or must be reached through a router.
  3. Default gateway — the IP address of the router on the local network that the host sends traffic to when the destination is outside its own subnet.
  4. DNS server — the server that translates human-readable names such as example.com into IP addresses. The Domain Name System listens on UDP/TCP port 53.
IP address192.168.1.10
Subnet mask255.255.255.0
Default gateway192.168.1.1
DNS server8.8.8.8

A host learns these settings either statically (typed in by an administrator) or automatically from a DHCP server. DHCP can supply the address, the mask, the gateway, and the DNS server in one exchange.

Part 4

Addressing and transmission

Communication depends on addresses being unique at every layer, because each layer answers a different question. If two devices in the same scope share an address, delivery breaks.

LayerAddressWhere it must be uniqueFailure if duplicated
Layer 2MAC addressOn the local link (LAN)Frames are delivered to the wrong device.
Layer 3IP addressAcross the internetwork (globally, or within the private scope)An IP conflict: traffic is misdelivered or dropped.
Layer 4Port numberPer host, per protocol, per connectionData is handed to the wrong application.

The MAC address is unique on the local network and is rewritten at every router hop. The IP address must be unique end to end. A socket — the combination of an IP address and a port number — identifies one specific conversation between two applications.

Unicast, multicast, and broadcast

A message can be addressed to one, some, or all recipients. These three modes appear constantly in exams and in protocol design.

ModeDestinationTypical example
UnicastOne sender to one receiverA web request to a server; by far the most common traffic
MulticastOne sender to a group of receiversStreaming video to subscribed viewers; IPv4 group range 224.0.0.0–239.255.255.255
BroadcastOne sender to all hosts on the local networkARP requests; IPv4 broadcast 255.255.255.255 (limited) or the subnet broadcast

Recall from Lesson 2 that the switch floods broadcast and multicast frames out of every port in the VLAN except the ingress port. At Layer 2 the broadcast address is ff:ff:ff:ff:ff:ff. IPv4 defines broadcasts; IPv6 has no broadcast and instead uses multicast (for example ff02::1, the all-nodes address).

Transmission mode · select one
Receiver 1 Receiver 2 Receiver 3 Receiver 4 Sender

Part 5

Bandwidth vs throughput

These two terms are related but not the same, and exams test the difference.

Definition — units. Data rates are measured in bits per second. The prefix tells you the scale, using decimal (SI) values: b/s, Kb/s (1,000 b/s), Mb/s (1,000,000 b/s), Gb/s (1,000,000,000 b/s), and Tb/s.
Case matters: b vs B. A lowercase b means bit; an uppercase B means byte, which is 8 bits. So a 1 Gb/s link carries 1,000,000,000 bits per second, while a file size of 1 GB is 8,000,000,000 bits — and downloading it over a 1 Gb/s link takes at least 8 seconds, not 1. Link speeds use b/s; file sizes use B. Confusing them is one of the most common mistakes in networking.
Standard Ethernet speedWritten asBits per second
Ethernet10 Mb/s10,000,000
Fast Ethernet100 Mb/s100,000,000
Gigabit Ethernet1 Gb/s1,000,000,000
10 Gigabit Ethernet10 Gb/s10,000,000,000
Download-time calculator · watch b vs B

Part 6

Latency, jitter, duplex and the data flow

Latency (also called delay) is the time it takes data to travel from source to destination. It is the sum of several parts:

Adding the time there and back gives the round-trip time (RTT), the figure the ping command reports. Jitter is the variation in latency between successive packets. A steady delay is tolerable, but variable delay causes choppy voice and video, so real-time traffic uses a buffer to smooth jitter out before playback. A network optimised for real-time media needs both low latency and low jitter.

Packet arrival · steady vs jittery

Duplex describes the direction(s) of data flow on a link. Half-duplex links carry one direction at a time and use CSMA/CD to recover from collisions. Full-duplex links carry both directions at once on a point-to-point connection, so collisions cannot occur. Modern switch-to-host and switch-to-switch links run full-duplex; a duplex mismatch degrades performance even though the link stays up.

The client-server data flow

With connectivity in place, a typical exchange between a client and a server follows a predictable path. Using the settings above, the client browses example.com:

  1. The client uses DNS (the configured DNS server) to translate example.com into an IP address.
  2. Because the server's address is outside the host's subnet (192.168.1.0/24), the host sends the traffic to its default gateway, 192.168.1.1.
  3. The frame travels to the switch, which forwards it within the LAN at Layer 2.
  4. The router accepts the frame, keeps the IP addresses, and builds a new frame for the next hop toward the Internet.
  5. The request crosses the Internet to the server, which returns a response along the reverse path.
Putting it together. Physical connectivity gets the bits onto the wire; the four logical settings get them to the right host and application. Bandwidth limits how much can flow, latency and jitter affect how smoothly it flows, and duplex decides whether traffic can flow both ways at once. Every later topic in the course — IP addressing, routing, switching, security — builds on these foundations.
Part 7 · Your turn

Review

Check what you have learned with these review questions.

Review · 6 questions

Sources

Sources & references

  1. Postel, J. RFC 791: Internet Protocol (1981) — 32-bit IPv4 addresses and the datagram header. rfc-editor.org/rfc/rfc791.
  2. Braden, R. RFC 1122: Requirements for Internet Hosts — Communication Layers (1989) — host addressing and the requirements for communication. rfc-editor.org/rfc/rfc1122.
  3. Droms, R. RFC 2131: Dynamic Host Configuration Protocol (1997) — automatic host configuration. rfc-editor.org/rfc/rfc2131.
  4. Alexander, S. & Droms, R. RFC 2132: DHCP Options and BOOTP Vendor Extensions (1997) — subnet mask (option 1), router/default gateway (option 3), and DNS (option 6). rfc-editor.org/rfc/rfc2132.
  5. IANA. IPv4 Address Space Registry and Service Name and Transport Protocol Port Number Registry. iana.org/assignments/ipv4-address-space.
  6. IEEE. IEEE 802.11™ Wireless LAN (wireless media) and IEEE 802.3™ Ethernet (copper and twisted-pair links). standards.ieee.org.
  7. Cisco. CCNA (200-301) Exam Topics, Network Fundamentals. cisco.com.

Target exams: CCNA 200-301 v1.1 · CyberOps Associate 200-201. Last content verification: 2026-10-11.