Week 1 · Lesson 17

OSI Model — Physical Layer

Layer 1 is the only layer that touches the real world. It turns a stream of binary digits into electrical voltages, pulses of light, or radio waves — and turns them back again. Everything above depends on it working.

CCNA 200-301 Domain 1.0 Network Fundamentals Verified 2026-10-11
Part 1

Layer 1 in the stack

The Physical layer is Layer 1, the bottom of the OSI model. It has no packets, no addresses and no protocol headers of its own. Its entire job is to put the bits produced by the Data Link layer onto a medium, and to recover those bits at the other end.

The Physical layer defines four things:

Medium

Copper cable, fibre-optic cable, or free-space radio.

Connectors

The connectors and pin layouts that join devices to the medium.

Signalling

How a 0 and a 1 are represented — voltage, light, or radio.

Encoding & timing

How a bit stream is framed and clocked.

Definition — physical layer. The physical layer (Layer 1) transfers raw bit streams over a physical medium. It defines the media, connectors, signalling, encoding, data rate, and the physical topology of the link.
Scope note. This lesson is the OSI-layer overview of Layer 1. The detailed treatment of cabling standards, pin-outs and media selection is Week 4.
Part 2

The job: transmit bits

When the Data Link layer hands down a frame, the Physical layer encodes the whole frame into a signal and transmits it. At the receiving side it senses the incoming signal, reconstructs the bits and passes them up. There are no source or destination addresses at Layer 1 — the interface simply pushes bits out and pulls bits in.

Three characteristics matter most at this layer:

CharacteristicMeaning
BandwidthThe theoretical capacity of the medium, often stated in bits per second (bps).
ThroughputThe actual rate of successful data transfer, usually lower than bandwidth because of overhead and interference.
LatencyThe time it takes a signal to travel from source to destination.
Bandwidth vs throughput · choose a medium and drag the slider

Part 3

Encoding bits as signals

Encoding is the rule that maps binary data onto signal states. The simplest scheme is NRZ (non-return-to-zero): one signal level represents a binary 1 and another represents a binary 0, and the level is held for the whole bit period.

A long run of identical bits produces no transitions, so the receiver can lose the clock. Real links therefore use richer encodings — such as Manchester or 4B/5B — that guarantee regular transitions.

Encoding · NRZ vs Manchester
1 0 1 1 0 1 0 0 1 = high 0 = low Each bit occupies one time slot across the eight-slot window.

Part 4

Media and connectors

Layer 1 spans three families of medium. Each balances cost, distance, bandwidth and immunity to interference differently.

MediumExamplesCharacter
Copper twisted pairUTP and STP categories (Cat 5e, 6, 6a) with RJ-45Cheap and easy to install; typical LAN runs up to about 100 m; susceptible to electromagnetic interference (EMI).
Coaxial cableEarly Ethernet and cable-TV networksHistorically important; largely replaced by twisted pair and fibre in modern LANs.
Fibre opticSingle-mode and multimode, with LC or SC connectorsVery high bandwidth over long distances; immune to EMI; single-mode reaches furthest, multimode is used for shorter runs.
WirelessRadio at 2.4 GHz, 5 GHz, and 6 GHzNo cable needed and supports mobility, but it is a shared medium and is affected by obstacles and interference.

Two fibre variants are tested: single-mode fibre (SMF) has a very small core and carries light from a laser over long distances, while multimode fibre (MMF) has a larger core, uses cheaper light sources, and is used for shorter distances such as inside a building or data centre.

Media families · pick one to compare

Every medium terminates in a connector. Three you should recognise on sight:

ConnectorMediumNotes
RJ-45Copper twisted pairAn 8-position, 8-contact connector (technically 8P8C) — the familiar LAN plug.
LCFibre opticA small form-factor fibre connector, often used in pairs (one for transmit, one for receive); common on modern transceivers.
SCFibre opticA square, push-pull fibre connector; older and larger than LC but still widely deployed.
Part 5

Duplex and the scale of the link

Duplex describes whether a device can send and receive at the same time.

Exam tip. If both ends of a link are set to full duplex, there is no collision domain on that link. A duplex mismatch (one end full, the other half) causes severe performance and error problems — a classic troubleshooting question. Also remember: a hub is half duplex and shares bandwidth; a switch gives each port its own full-duplex link.

The physical layer looks different depending on the scale of the network:

AspectLANWAN
DistanceShort — a room, building, or campus.Long — across cities, countries, or continents.
OwnershipOwned and managed by the organisation.Usually leased from a service provider.
Typical mediaTwisted pair, fibre, and Wi-Fi.Fibre, leased lines, and carrier wireless links.
Part 6

Physical-layer devices and the PDU

Three device categories are tied to Layer 1.

The Layer 1 PDU is a bit. At this layer there are no headers, no addresses and no error detection — just a stream of ones and zeros encoded as signals on the medium.

Remember the PDU ladder. Layer 4: segment (TCP) or datagram (UDP). Layer 3: packet. Layer 2: frame. Layer 1: bits. Encapsulation stops at Layer 2; Layer 1 just transmits the finished frame as signals.
The PDU ladder · select a layer

Part 7 · Your turn

Review

Check what you have learned with these review questions.

Review · 6 questions

The Physical layer is the OSI layer that transmits raw bits over a medium; it defines media, connectors, signalling and encoding.

TermMeaning
EncodingThe mapping of binary data onto signal states (for example NRZ, Manchester).
UTP / STPUnshielded / shielded twisted pair copper cabling.
Single-mode fibreFibre with a small core, used with lasers for long-distance links.
Multimode fibreFibre with a larger core, used for shorter-distance links.
RJ-45The 8P8C copper connector used for twisted-pair Ethernet.
Half duplexSend or receive but not both at once; collisions are possible.
Full duplexSend and receive simultaneously; no collisions.
TransceiverA device or module that converts signals between media or connector types.
Sources & references
  1. Postel, J. RFC 791: Internet Protocol (1981). rfc-editor.org/rfc/rfc791.
  2. Braden, R. RFC 1122: Requirements for Internet Hosts — Communication Layers (1989). rfc-editor.org/rfc/rfc1122.
  3. IEEE. IEEE 802.3 (Ethernet; physical media and connectors). standards.ieee.org.
  4. IEEE. IEEE 802.11 (Wireless LAN). standards.ieee.org.
  5. ISO/IEC. 7498-1:1994 — Open Systems Interconnection — Basic Reference Model. iso.org.
  6. Cisco. CCNA (200-301) Exam Topics, Network Fundamentals. cisco.com.
Sources

Sources & references

  1. Postel, J. RFC 791: Internet Protocol (1981). rfc-editor.org/rfc/rfc791.
  2. Braden, R. RFC 1122: Requirements for Internet Hosts — Communication Layers (1989). rfc-editor.org/rfc/rfc1122.
  3. IEEE. IEEE 802.3 (Ethernet; physical media and connectors). standards.ieee.org.
  4. IEEE. IEEE 802.11 (Wireless LAN). standards.ieee.org.
  5. ISO/IEC. 7498-1:1994 — Open Systems Interconnection — Basic Reference Model. iso.org.
  6. Cisco. CCNA (200-301) Exam Topics, Network Fundamentals. cisco.com.

Target exams: CCNA 200-301 v1.1 · CyberOps Associate 200-201. Last content verification: 2026-10-11.