OSI Model — Physical Layer
Layer 1 is the only layer that touches the real world. It turns a stream of binary digits into electrical voltages, pulses of light, or radio waves — and turns them back again. Everything above depends on it working.
Layer 1 in the stack
The Physical layer is Layer 1, the bottom of the OSI model. It has no packets, no addresses and no protocol headers of its own. Its entire job is to put the bits produced by the Data Link layer onto a medium, and to recover those bits at the other end.
The Physical layer defines four things:
Medium
Copper cable, fibre-optic cable, or free-space radio.
Connectors
The connectors and pin layouts that join devices to the medium.
Signalling
How a 0 and a 1 are represented — voltage, light, or radio.
Encoding & timing
How a bit stream is framed and clocked.
The job: transmit bits
When the Data Link layer hands down a frame, the Physical layer encodes the whole frame into a signal and transmits it. At the receiving side it senses the incoming signal, reconstructs the bits and passes them up. There are no source or destination addresses at Layer 1 — the interface simply pushes bits out and pulls bits in.
Three characteristics matter most at this layer:
| Characteristic | Meaning |
|---|---|
| Bandwidth | The theoretical capacity of the medium, often stated in bits per second (bps). |
| Throughput | The actual rate of successful data transfer, usually lower than bandwidth because of overhead and interference. |
| Latency | The time it takes a signal to travel from source to destination. |
Encoding bits as signals
Encoding is the rule that maps binary data onto signal states. The simplest scheme is NRZ (non-return-to-zero): one signal level represents a binary 1 and another represents a binary 0, and the level is held for the whole bit period.
A long run of identical bits produces no transitions, so the receiver can lose the clock. Real links therefore use richer encodings — such as Manchester or 4B/5B — that guarantee regular transitions.
Media and connectors
Layer 1 spans three families of medium. Each balances cost, distance, bandwidth and immunity to interference differently.
| Medium | Examples | Character |
|---|---|---|
| Copper twisted pair | UTP and STP categories (Cat 5e, 6, 6a) with RJ-45 | Cheap and easy to install; typical LAN runs up to about 100 m; susceptible to electromagnetic interference (EMI). |
| Coaxial cable | Early Ethernet and cable-TV networks | Historically important; largely replaced by twisted pair and fibre in modern LANs. |
| Fibre optic | Single-mode and multimode, with LC or SC connectors | Very high bandwidth over long distances; immune to EMI; single-mode reaches furthest, multimode is used for shorter runs. |
| Wireless | Radio at 2.4 GHz, 5 GHz, and 6 GHz | No cable needed and supports mobility, but it is a shared medium and is affected by obstacles and interference. |
Two fibre variants are tested: single-mode fibre (SMF) has a very small core and carries light from a laser over long distances, while multimode fibre (MMF) has a larger core, uses cheaper light sources, and is used for shorter distances such as inside a building or data centre.
Every medium terminates in a connector. Three you should recognise on sight:
| Connector | Medium | Notes |
|---|---|---|
| RJ-45 | Copper twisted pair | An 8-position, 8-contact connector (technically 8P8C) — the familiar LAN plug. |
| LC | Fibre optic | A small form-factor fibre connector, often used in pairs (one for transmit, one for receive); common on modern transceivers. |
| SC | Fibre optic | A square, push-pull fibre connector; older and larger than LC but still widely deployed. |
Duplex and the scale of the link
Duplex describes whether a device can send and receive at the same time.
- Half duplex — a device may either transmit or receive, but not both at once. The medium is shared, so collisions can occur and media-access rules are needed to manage them. Hubs and older shared Ethernet operated this way.
- Full duplex — a device transmits and receives simultaneously on separate paths. There is no contention, so collisions do not occur. Modern switched Ethernet is full duplex everywhere a host connects to a switch port.
The physical layer looks different depending on the scale of the network:
| Aspect | LAN | WAN |
|---|---|---|
| Distance | Short — a room, building, or campus. | Long — across cities, countries, or continents. |
| Ownership | Owned and managed by the organisation. | Usually leased from a service provider. |
| Typical media | Twisted pair, fibre, and Wi-Fi. | Fibre, leased lines, and carrier wireless links. |
Physical-layer devices and the PDU
Three device categories are tied to Layer 1.
- NIC (Network Interface Card) — the host’s interface to the medium. Its physical side transmits and receives signals; it also carries the MAC address used by Layer 2, so a NIC spans Layer 1 and Layer 2.
- Repeaters and hubs — regenerate and repeat signals to extend a link. A hub is a multi-port repeater: it repeats an incoming signal out every other port. Both operate purely at the physical layer and do not read addresses.
- Transceivers — convert a signal from one form or connector to another (for example, an optical transceiver module that plugs into a switch and drives a fibre link).
The Layer 1 PDU is a bit. At this layer there are no headers, no addresses and no error detection — just a stream of ones and zeros encoded as signals on the medium.
Review
Check what you have learned with these review questions.
The Physical layer is the OSI layer that transmits raw bits over a medium; it defines media, connectors, signalling and encoding.
| Term | Meaning |
|---|---|
| Encoding | The mapping of binary data onto signal states (for example NRZ, Manchester). |
| UTP / STP | Unshielded / shielded twisted pair copper cabling. |
| Single-mode fibre | Fibre with a small core, used with lasers for long-distance links. |
| Multimode fibre | Fibre with a larger core, used for shorter-distance links. |
| RJ-45 | The 8P8C copper connector used for twisted-pair Ethernet. |
| Half duplex | Send or receive but not both at once; collisions are possible. |
| Full duplex | Send and receive simultaneously; no collisions. |
| Transceiver | A device or module that converts signals between media or connector types. |
- Postel, J. RFC 791: Internet Protocol (1981). rfc-editor.org/rfc/rfc791.
- Braden, R. RFC 1122: Requirements for Internet Hosts — Communication Layers (1989). rfc-editor.org/rfc/rfc1122.
- IEEE. IEEE 802.3 (Ethernet; physical media and connectors). standards.ieee.org.
- IEEE. IEEE 802.11 (Wireless LAN). standards.ieee.org.
- ISO/IEC. 7498-1:1994 — Open Systems Interconnection — Basic Reference Model. iso.org.
- Cisco. CCNA (200-301) Exam Topics, Network Fundamentals. cisco.com.
Sources & references
- Postel, J. RFC 791: Internet Protocol (1981). rfc-editor.org/rfc/rfc791.
- Braden, R. RFC 1122: Requirements for Internet Hosts — Communication Layers (1989). rfc-editor.org/rfc/rfc1122.
- IEEE. IEEE 802.3 (Ethernet; physical media and connectors). standards.ieee.org.
- IEEE. IEEE 802.11 (Wireless LAN). standards.ieee.org.
- ISO/IEC. 7498-1:1994 — Open Systems Interconnection — Basic Reference Model. iso.org.
- Cisco. CCNA (200-301) Exam Topics, Network Fundamentals. cisco.com.
Target exams: CCNA 200-301 v1.1 · CyberOps Associate 200-201. Last content verification: 2026-10-11.