Week 2 · Lesson 2

Network Components

Week 1 gave you the two buckets — end devices and intermediary devices. This lesson re-opens both buckets to look inside: how a switch decides, how a router decides, what the three media are and why each exists, and how networks are documented.

CCNA 200-301 Domain 1.0 Network Fundamentals Verified 2026-10-11
Part 1

End devices (hosts)

An end device, also called a host, is the source or destination of network traffic. It runs the applications people actually use — a browser, a phone call, a database — and every host carries a network address (such as an IP address) so the network can deliver data to it.

Definition — host. A host is any device that originates or receives network traffic. Whether it is a PC or a temperature sensor, it occupies a role at the edge of the network — the data starts here or stops here.

The first line on a network diagram is usually drawn your way from a host’s perspective: each server has an address, each client has an address, and the network in between is responsible for delivering data between those addresses.

Part 2

Intermediary devices and how they decide

Intermediary devices sit between hosts. They do not originate user data; they forward it. What makes them different from each other is the address they read to make the forwarding decision. Week 1’s one-line rule holds, and now we add the mechanism:

DeviceReadsHow it decides to forwardWhy it works
SwitchLayer 2 (MAC)Looks up the destination MAC in its MAC address table. Known address → forward out that port; unknown → flood to every port except the one it came in on.Keeps traffic within one local network (LAN).
RouterLayer 3 (IP)Looks up the destination IP in its routing table, matching the longest prefix, then builds a brand-new Layer 2 frame for the next hop.Moves packets between different networks.
Wireless access point (WAP)Layer 2 (MAC, via radio)Acts as a transparent bridge: associates wireless clients, then forwards their frames into the wired LAN using MAC addresses, exactly like a switch port.Brings Wi-Fi hosts into the same LAN as wired hosts.
FirewallHeaders up to Layers 3–4 (and deeper)Compares traffic against a security policy and either permits or denies it; can drop traffic that a switch or router would happily forward.Enforces the boundary of trust at the network edge.
How does it decide? · select a device

Switch

Exam tip. The favourite trick is asking which address each device reads. Anchor yourself: switch = MAC = inside one LAN; router = IP = between LANs; AP = MAC over radio = same LAN, wireless; firewall = policy = permit or deny. A device that reads neither address but applies rules is a firewall.

Two finer points worth remembering:

Part 3

The three network media

The medium is the physical path the signal travels. There are only three families, and the exam expects you to know what each is good at:

MediumUsed forPros (one line)Cons (one line)
Copper (UTP / STP)Ethernet LAN cabling (IEEE 802.3); twisted pairs keep signals clean.Cheap, easy to terminate, perfect for desks and rooms.Limited range (~100 m per segment for twisted pair), suffers interference, must be run safely with respect to power.
Fibre opticBackbones, server links, and long outdoor spans.Huge bandwidth over long distances (kilometres), immune to electromagnetic interference.Costlier components, delicate, needs special skills to terminate, and the electronics are more expensive.
WirelessMobility — clients that move (IEEE 802.11 Wi-Fi and cellular).No cable needed; users roam with their devices.Subject to interference and range limits; half-duplex shared medium; needs strong security.
Three media · select one

Within copper there are two Canadian-style families: UTP (Unshielded Twisted Pair) — the ordinary Ethernet cable — and STP (Shielded Twisted Pair), which adds a shield around the pairs to block more interference at a higher price. Within fibre, the two flavours are single-mode (thin core, laser, runs the longest distances) and multi-mode (thicker core, LED, shorter runs such as within a building). You will meet the cabling details again in the physical-layer week.

How to remember. Copper = short and cheap. Fibre = long and fast, immune to noise. Wireless = convenient, no cable, but shared and noisy environment. When a scenario says “a warehouse with forklift trucks moving between buildings,” think wireless for the workers and fibre between the buildings.
Part 4

Network representations and documentation

Networks are drawn in three ways, and Cisco uses all three in the same documents:

Diagrams are backed by documentation, and accuracy matters for three reasons:

  1. Troubleshooting: a wrong label — the wrong port number, VLAN, or IP range — sends an engineer investigating the wrong segment.
  2. Change planning: adding a new switch or router requires knowing what is already plugged in, where, and at what speed.
  3. Security and audit: you cannot protect or inventory what is not recorded; undocumented devices are exactly where attackers hide.
Documentation gap · what does it cost?

Remember for the exam. “Accurate documentation” is a recurring theme, almost always phrased as: documentation must match reality. A diagram that is prettier but wrong is worse than one that is ugly but true. When a scenario mentions a device that is not on the diagram, the answer is usually “check the documentation / verify what is actually connected.”
Part 5

A medium-size enterprise topology

Here is a typical small-to-medium enterprise network, drawn with the icon vocabulary you will see all course long. Trace the story: the cloud is the Internet; the edge router is the only gateway in and out; the DMZ server is deliberately separate; and the distribution switch fans out to access switches, access point, and internal servers.

Enterprise topology · select a role to highlight it
Internet Edge router Web server DMZ File server Distribution switch Access switch A Access switch B Access point PC 1 PC 2 Printer PC 3 PC 4 Laptop Wi-Fi

Exam tip. In a diagram like this, be able to answer three questions on sight: (1) How many LANs? One — every host behind the edge router is in the same logical campus network. (2) Where is the boundary? The edge router is the Layer 3 gateway. (3) Which host cannot reach the file server if the distribution switch fails? All of them — that is exactly the single point of failure redundancy is meant to fix.
Part 6

Sources & references

  1. Cisco Networking Academy. Introduction to Networks (ITN), Module 1 — Networking Today: “Components of a Network” and “Network Representations and Topologies”. skillsforall.com.
  2. IEEE. IEEE 802.3 (Ethernet over UTP/STP and fibre). standards.ieee.org.
  3. IEEE. IEEE 802.11 (wireless LAN medium). standards.ieee.org.
  4. Cisco. CCNA (200-301) Exam Topics, Network Fundamentals (1.0). cisco.com.
Part 7 · Your turn

Review

Check what you have learned with these review questions.

Review · 6 questions

Target exams: CCNA 200-301 v1.1 · CyberOps Associate 200-201. Last content verification: 2026-10-11.