Week 2 · Lesson 12

Topology Comparison

The same network has two topologies at once: the physical one you can see with cables, and the logical one data actually follows. This lesson defines both and then compares the classic shapes — point-to-point, star, mesh, bus, and ring — by their advantages, disadvantages, and typical use.

CCNA 200-301 Domain 1.0 Network Fundamentals Verified 2026-10-11
Part 1

Physical vs logical topology

Every network has two answers to the question “how is it laid out?” They are not the same, and confusing them is a common exam trap.

Definition — physical vs logical topology. A physical topology is the actual layout of cables, ports, and devices — what you would draw if you traced every wire by hand. A logical topology is the path that data actually takes and how devices appear to communicate — the addressing, VLANs, and forwarding rules.

The two can disagree completely. A modern office is wired as a physical star: every PC runs a cable to a central switch. But the logical picture is different again — a switch forwards frames only where they need to go, and VLANs can carve the building into several logical networks that ignore the physical cabling. A building physically wired as a star can behave logically like a set of separate networks, or even like a ring in some legacy token-ring deployments.

Same four devices, two topologies · toggle the view
Physical (star) Switch PC 1 PC 2 PC 3 PC 4 Logical (ring) PC 1 PC 2 PC 4 PC 3

Part 2

Point-to-point, star and hub-and-spoke

Two shapes cover most of what you will build or read about.

Classic shapes · select one

Point-to-point

A point-to-point link joins exactly two devices and nothing else. There is one path, dedicated to those two endpoints, so bandwidth is guaranteed and there is no sharing or contention. Point-to-point links are the building block of WANs: a serial link between two branch routers, or a leased line from a site to a provider, is a point-to-point connection.

Star and hub-and-spoke

In a star topology every device connects to one central device (a switch, hub, or access point). All traffic passes through the centre. Hub-and-spoke is the WAN cousin: a central hub site with spoke sites attached to it, where the centre is typically a router rather than a switch.

Why the star wins. The star dominates modern LANs because a switch removes the old weakness: though the centre is still a single point of failure, it forwards a frame only to the port that needs it, and adding a link does not disturb the others. That is why “star” and “switched Ethernet” go together.
Part 3

Full mesh and partial mesh

In a full mesh, every node connects directly to every other node. If there are n nodes, the number of links is n(n−1)/2 — because each of the n nodes links to the other n−1, and each link is counted twice.

Mesh link counter · set the number of nodes

Exam tip. Know the formula. A full mesh of n devices needs n(n−1)/2 links and n−1 links per device. Four sites = 6 links; five = 10 links. Questions often give the number of sites and ask for the link count (or the reverse).

Partial mesh

A partial mesh is a compromise: some nodes are fully interconnected, while others connect to only one or two neighbours. It delivers most of the redundancy of a full mesh at a fraction of the cost, because only the busiest or most critical links are doubled.

Part 4

Bus and ring

Two shapes that explain a lot of exam questions — because they are legacy, and because their weaknesses are severe.

Bus or ring? · select one
Bus terminator terminator PC 1 PC 2 PC 3 PC 4 Ring PC 1 PC 2 PC 4 PC 3

Bus

A bus topology uses a single shared backbone cable (the bus) to which every device taps in; both ends of the cable are terminated. Any signal put on the bus is heard by all devices.

Watch out. “Star” and “bus” are easy to confuse when a hub is drawn in the centre. A hub-based Ethernet is physically a star but electrically behaves like a bus, because a hub repeats every signal out of every port. A switch truly behaves like a star, forwarding to one port.

Ring

In a ring, each device connects to exactly two neighbours, forming a closed loop. Data travels around the ring from node to node; in a dual ring there are two paths so that a single break can be routed around.

Part 5

The comparison table

This table summarises everything above. Learn it as a set of trade-offs, not as separate facts: the one theme running through the whole list is that redundancy costs money and complexity, while cheap and simple means fewer safety nets.

TopologyAdvantagesDisadvantagesTypical use
Point-to-pointSimplest; dedicated, predictable bandwidth; one path only.Links only two nodes; many sites become a mesh.WAN links between two sites; leased lines.
Star / hub-and-spokeEasy to add or remove nodes; centralised management; a bad node affects only its own segment.Central device is a single point of failure and a bottleneck.Switched Ethernet LANs, wireless, branch WANs.
Full meshMaximum redundancy and performance; direct path between all pairs.Costly; n(n−1)/2 links; hard to manage as it grows.Small critical cores; spine-leaf tier links.
Partial meshGood redundancy at moderate cost; suited to real budgets.More complex routing and planning than a star.Most enterprise WANs; large campus cores.
BusCheap and simple for a few nodes; no central device.One break downs the whole network; shared collision domain; hard to troubleshoot.Legacy Ethernets (10BASE5/10BASE2); historical only.
RingOrderly access; a dual ring survives one failure.A single-ring break drops the network; latency grows through intermediate nodes.Legacy Token Ring/FDDI; provider metro rings.
Note. Real networks mix these. A campus is a star at the access layer, a partial mesh between distribution and core, and a dual-homed (two-link) connection to the Internet. The exam describes the dominant shape at each layer, not a single pure topology.
Part 6

Choose a topology

The last skill is matching a requirement to a shape. The table below is the revision sheet for that decision.

RequirementBest-fit topologyWhy
Every PC connects to one central switchStarAdding or removing a PC touches one cable, and a faulty PC affects only its own segment. The centre remains a single point of failure, so production designs back it up.
20 branches on a limited budgetHub-and-spoke or partial meshA full mesh would need 190 links. A hub-and-spoke costs 19; a partial mesh adds a few direct links between the busiest sites to remove the hub as a single point of failure.
3 critical routersFull meshn(n−1)/2 = 3×2/2 = 3 links. Any one link can fail and traffic still flows, and each router has a direct path to both others.
An old coax backboneBusA shared backbone with terminators at both ends. Cheap and simple, but one break takes down every device on it, so it survives only in legacy or very small installations.
Part 7 · Your turn

Review

Check what you have learned with these review questions.

Review · 6 questions

Sources

Sources & references

  1. Cisco. CCNA (200-301) Exam Topics, Domain 1.0 Network Fundamentals. cisco.com.
  2. IEEE. IEEE 802.3 Ethernet Standard (legacy bus and star physical topologies). standards.ieee.org.
  3. IEEE. IEEE 802.5 Token Ring Standard (ring topology). standards.ieee.org.
  4. Tanenbaum, A. S. & Wetherall, D. J. Computer Networks, 5th ed., Chapter 1 (network topologies and classification).

Target exams: CCNA 200-301 v1.1 · CyberOps Associate 200-201. Last content verification: 2026-10-11.