Introduction to the Physical Layer
Every segment, packet and frame you built in Weeks 1–3 ends its life as a stream of 1s and 0s — a voltage on copper, a pulse of light in fibre, a radio wave in the air. The physical layer owns that final journey. This lesson defines what the physical layer does, what its standards control, and how it fits underneath everything else.
What the physical layer does
The physical layer is OSI Layer 1. It has exactly one job: move a bit from one device to another. It takes the frame handed down by the data link layer, turns that frame into a physical signal, and places the signal on the medium. At the far end the receiving physical layer does the reverse: it senses the signal and rebuilds the bits.
Critically, the physical layer does not read addresses, does not care about IP or MAC, and does not understand frames. Those jobs belong to Layers 2 and above. Layer 1 knows only the physical reality of the link: which voltage means 1, how long a bit lasts, and how fast bits can be sent. Its unit of data is the bit — that is the PDU at Layer 1.
PDU — bit
Frames belong to Layer 2, packets to Layer 3, segments to Layer 4. Layer 1 moves single bits.
Signal
A physical variation: voltage on copper, light in fibre, power/frequency/phase in radio.
Medium
The path the signal travels: copper, fibre or free space. Layer 1 rules are written per medium.
What the physical layer standardises
For two devices from two different vendors to exchange bits, both must agree on the physical rules. Physical-layer standards pin down five things.
| Element | What it decides | Example |
|---|---|---|
| Media type | What carries the signal: copper, optical fibre, or wireless. | Cat6 UTP; multimode fibre; Wi-Fi |
| Connectors | The physical plug/socket that joins devices to the medium. | RJ-45 (8P8C); LC/SC fibre; coax BNC |
| Encoding | How a bit pattern is mapped to symbols on the medium. | NRZ, Manchester, 4B/5B, PAM-5 |
| Signalling | Which physical state represents a 1 and a 0. | High/low voltage; light on/off; RF level |
| Speed & duplex | How fast bits are sent and whether both ends can send at once. | 1 Gbps, full duplex |
Four things every encoding must define
Encoding turns bits into signal elements and back. Whichever scheme a technology uses — NRZ, Manchester, 4B/5B or PAM-5 — it must answer the same four questions. Work through them one at a time.
1 to the high level and 0 to the low level. Its weakness is that a long run of the same bit produces no transitions, which breaks clock recovery. Lesson 2 shows this on a waveform and explains how schemes such as Manchester fix it.LAN physical vs WAN physical
There are two very different worlds of physical-layer standards, and the exam expects you to keep them apart.
LAN physical specifications come from the Ethernet family (IEEE 802.3). The name tells you everything: in 1000BASE-T, 1000 is the speed in Mbps, BASE means baseband signalling, and T means twisted-pair copper. 1000BASE-T (Gigabit Ethernet) runs over four pairs of Cat5 (or better) UTP to a maximum of 100 m and uses all four pairs in both directions at once.
| Ethernet name | Speed | IEEE standard | Media |
|---|---|---|---|
| 10BASE-T | 10 Mbps | 802.3i | 2-pair UTP, 100 m |
| 100BASE-TX | 100 Mbps | 802.3u | 2-pair UTP, 100 m |
| 1000BASE-T | 1 Gbps | 802.3ab | 4-pair UTP, 100 m |
| 10GBASE-T | 10 Gbps | 802.3an | UTP/STP, up to 100 m (Cat6a) |
WAN physical circuits are the leased lines and telecom services that connect sites over long distances. These are defined by carriers and telecom bodies (ITU-T, ANSI) rather than by IEEE 802.3, and use different framing, connectors and distances:
- T1 — a North American digital carrier line of 1.544 Mbps (24 channels of 64 kbps).
- E1 — the European equivalent at 2.048 Mbps (32 channels).
- DSL — broadband over an ordinary telephone pair (ITU-T G.992).
- SONET / SDH — high-speed optical backbone services.
| LAN physical (Ethernet) | WAN physical (telecom) | |
|---|---|---|
| Standard body | IEEE 802.3 | ITU-T, ANSI, carriers |
| Typical media | UTP/STP copper, fibre | Telco copper, fibre, coax, radio |
| Distance | Up to about 100 m on copper | Kilometres |
| Ownership | You own the cabling | Leased from a provider |
| Example | 1000BASE-T | T1 / E1, DSL, SONET |
Standards bodies
Different organisations own different pieces of the physical world. Learn who owns what:
| Body | Owns | Key standard |
|---|---|---|
| IEEE | Ethernet data link and physical layers (LANs). | IEEE 802.3 |
| TIA / EIA | Commercial structured cabling: cable categories, connectors, channel length. | ANSI/TIA-568 |
| ISO | International generic cabling and reference models. | ISO/IEC 11801 |
| ITU-T | Telecom / WAN standards and interfaces. | G.992 (ADSL) |
| ANSI | Accredits and co-publishes the 568 cabling standards. | ANSI/TIA-568.2-D |
Where the physical layer sits
Recalling Week 3's encapsulation model, the PDU chain ends at Layer 1: data → segment/datagram → packet → frame → bits. The physical layer is the foundation everything else stands on, and its hardware lives in the network interface card (NIC) plus the PHY circuitry of the port.
Layer 1 is the foundation of the stack. Every upper-layer header, however complex, is finally serialised into bits and pushed onto the medium. The receiving NIC reverses the process and hands the frame back up the stack.
Why it still matters
Most “the network is down” incidents are physical. Knowing the layer lets you reason about the cause instead of guessing:
- No link light. Wrong media, bad connector, or a cable that exceeds its rated distance — all Layer 1 faults.
- Slow or erroring link. A speed/duplex mismatch, a cable category too low for the speed, or electromagnetic interference on the run.
- Intermittent drops. Damaged copper, a marginal fibre bend, or a connector that is only partly seated.
Because Layer 1 is beneath everything, a Layer 1 fault is invisible to the higher layers until it breaks them. That is why troubleshooting almost always starts at the bottom of the stack.
Review
Check what you have learned with these review questions.
Sources & references
- IEEE. IEEE 802.3 Ethernet Working Group — LAN/MAN physical and data-link specifications. standards.ieee.org/ieee/802.3.
- TIA. ANSI/TIA-568.2-D, Balanced Twisted-Pair Telecommunications Cabling and Components Standard (2018). tiaonline.org.
- ISO/IEC. ISO/IEC 11801-1:2017, Generic cabling for customer premises — Part 1: General requirements. iso.org/standard/66182.html.
- ITU-T. Recommendation G.992 (ADSL transceivers). itu.int/rec/T-REC-G.992.
- Cisco. CCNA (200-301) Exam Topics, Domain 1.6 (physical interfaces and cabling). cisco.com.
Target exams: CCNA 200-301 v1.1 · CyberOps Associate 200-201. Last content verification: 2026-10-11.