Week 4 · Lesson 1

Introduction to the Physical Layer

Every segment, packet and frame you built in Weeks 1–3 ends its life as a stream of 1s and 0s — a voltage on copper, a pulse of light in fibre, a radio wave in the air. The physical layer owns that final journey. This lesson defines what the physical layer does, what its standards control, and how it fits underneath everything else.

CCNA 200-301 Domain 1.6 Physical Interfaces & Cabling Verified 2026-10-11
Part 1

What the physical layer does

The physical layer is OSI Layer 1. It has exactly one job: move a bit from one device to another. It takes the frame handed down by the data link layer, turns that frame into a physical signal, and places the signal on the medium. At the far end the receiving physical layer does the reverse: it senses the signal and rebuilds the bits.

Definition — physical layer. The part of the network stack that transmits raw bits across a medium by converting them to signals — electrical voltage on copper, pulses of light on fibre, or radio/electromagnetic waves in the air — and converting signals back to bits on reception.

Critically, the physical layer does not read addresses, does not care about IP or MAC, and does not understand frames. Those jobs belong to Layers 2 and above. Layer 1 knows only the physical reality of the link: which voltage means 1, how long a bit lasts, and how fast bits can be sent. Its unit of data is the bit — that is the PDU at Layer 1.

PDU — bit

Frames belong to Layer 2, packets to Layer 3, segments to Layer 4. Layer 1 moves single bits.

Signal

A physical variation: voltage on copper, light in fibre, power/frequency/phase in radio.

Medium

The path the signal travels: copper, fibre or free space. Layer 1 rules are written per medium.

The OSI stack · select a layer

Part 2

What the physical layer standardises

For two devices from two different vendors to exchange bits, both must agree on the physical rules. Physical-layer standards pin down five things.

ElementWhat it decidesExample
Media typeWhat carries the signal: copper, optical fibre, or wireless.Cat6 UTP; multimode fibre; Wi-Fi
ConnectorsThe physical plug/socket that joins devices to the medium.RJ-45 (8P8C); LC/SC fibre; coax BNC
EncodingHow a bit pattern is mapped to symbols on the medium.NRZ, Manchester, 4B/5B, PAM-5
SignallingWhich physical state represents a 1 and a 0.High/low voltage; light on/off; RF level
Speed & duplexHow fast bits are sent and whether both ends can send at once.1 Gbps, full duplex
Everything from the shape of the RJ-45 plug to the precise voltage swing on a wire is written into a standard, so that a cable bought in one country plugs into a switch built in another.
The five things a physical standard defines · select one

Part 3

Four things every encoding must define

Encoding turns bits into signal elements and back. Whichever scheme a technology uses — NRZ, Manchester, 4B/5B or PAM-5 — it must answer the same four questions. Work through them one at a time.

Encoding checklist · step through the four requirements
1 of 4

Note. The simplest scheme, NRZ (non-return to zero), maps 1 to the high level and 0 to the low level. Its weakness is that a long run of the same bit produces no transitions, which breaks clock recovery. Lesson 2 shows this on a waveform and explains how schemes such as Manchester fix it.
Part 4

LAN physical vs WAN physical

There are two very different worlds of physical-layer standards, and the exam expects you to keep them apart.

LAN physical specifications come from the Ethernet family (IEEE 802.3). The name tells you everything: in 1000BASE-T, 1000 is the speed in Mbps, BASE means baseband signalling, and T means twisted-pair copper. 1000BASE-T (Gigabit Ethernet) runs over four pairs of Cat5 (or better) UTP to a maximum of 100 m and uses all four pairs in both directions at once.

Ethernet nameSpeedIEEE standardMedia
10BASE-T10 Mbps802.3i2-pair UTP, 100 m
100BASE-TX100 Mbps802.3u2-pair UTP, 100 m
1000BASE-T1 Gbps802.3ab4-pair UTP, 100 m
10GBASE-T10 Gbps802.3anUTP/STP, up to 100 m (Cat6a)

WAN physical circuits are the leased lines and telecom services that connect sites over long distances. These are defined by carriers and telecom bodies (ITU-T, ANSI) rather than by IEEE 802.3, and use different framing, connectors and distances:

LAN physical (Ethernet)WAN physical (telecom)
Standard bodyIEEE 802.3ITU-T, ANSI, carriers
Typical mediaUTP/STP copper, fibreTelco copper, fibre, coax, radio
DistanceUp to about 100 m on copperKilometres
OwnershipYou own the cablingLeased from a provider
Example1000BASE-TT1 / E1, DSL, SONET

Standards bodies

Different organisations own different pieces of the physical world. Learn who owns what:

BodyOwnsKey standard
IEEEEthernet data link and physical layers (LANs).IEEE 802.3
TIA / EIACommercial structured cabling: cable categories, connectors, channel length.ANSI/TIA-568
ISOInternational generic cabling and reference models.ISO/IEC 11801
ITU-TTelecom / WAN standards and interfaces.G.992 (ADSL)
ANSIAccredits and co-publishes the 568 cabling standards.ANSI/TIA-568.2-D
Exam tip. Remember the split: IEEE 802.3 defines Ethernet (how frames and PHYs work); TIA/EIA-568 defines the cabling you buy (categories, connectors, the 100 m channel). A question about “how many metres a Cat6a channel may run” is a cabling (TIA) question; a question about “the frame format on the wire” is an IEEE 802.3 question.
Decode an Ethernet name · select a specification

Part 5

Where the physical layer sits

Recalling Week 3's encapsulation model, the PDU chain ends at Layer 1: data → segment/datagram → packet → frame → bits. The physical layer is the foundation everything else stands on, and its hardware lives in the network interface card (NIC) plus the PHY circuitry of the port.

Host A NIC / PHY Layer 1 Layers 2–7 Host B NIC / PHY Layer 1 Layers 2–7 the medium 1 0 1 1 0 1 0 1 bits travel as voltage, light or radio PDU = bits data → segment → packet → frame → bits

Layer 1 is the foundation of the stack. Every upper-layer header, however complex, is finally serialised into bits and pushed onto the medium. The receiving NIC reverses the process and hands the frame back up the stack.

Part 6

Why it still matters

Most “the network is down” incidents are physical. Knowing the layer lets you reason about the cause instead of guessing:

Because Layer 1 is beneath everything, a Layer 1 fault is invisible to the higher layers until it breaks them. That is why troubleshooting almost always starts at the bottom of the stack.

Key terms. Physical layer (Layer 1) — transmits raw bits over a medium as signals. PDU — a bit. Encoding — mapping bits to signal elements. Signalling — which physical state means 1 or 0. Bit interval — the time one bit occupies on the medium. Baseband — encoding the signal directly onto the medium, with no carrier. PHY — the physical-layer circuitry of a network port.
Part 7 · Your turn

Review

Check what you have learned with these review questions.

Review · 6 questions

Sources

Sources & references

  1. IEEE. IEEE 802.3 Ethernet Working Group — LAN/MAN physical and data-link specifications. standards.ieee.org/ieee/802.3.
  2. TIA. ANSI/TIA-568.2-D, Balanced Twisted-Pair Telecommunications Cabling and Components Standard (2018). tiaonline.org.
  3. ISO/IEC. ISO/IEC 11801-1:2017, Generic cabling for customer premises — Part 1: General requirements. iso.org/standard/66182.html.
  4. ITU-T. Recommendation G.992 (ADSL transceivers). itu.int/rec/T-REC-G.992.
  5. Cisco. CCNA (200-301) Exam Topics, Domain 1.6 (physical interfaces and cabling). cisco.com.

Target exams: CCNA 200-301 v1.1 · CyberOps Associate 200-201. Last content verification: 2026-10-11.