Week 4 · Lesson 3

Copper Cabling

Most network drops in the world are copper. To specify, install, or troubleshoot them you need three things cold: what limits copper, the category that reaches a given speed at a given distance, and the 100 m channel rule. The numbers in this lesson are the ones the exam expects — learn them exactly.

CCNA 200-301 Domain 1.6 Physical Interfaces & Cabling Verified 2026-10-11
Part 1

Why copper?

Copper is inexpensive, easy to terminate, and — crucially — it conducts electricity, so it can carry data as electrical signals. A changing voltage on a copper pair represents the bits from the previous lesson. Copper is the default medium for horizontal cabling inside buildings because it is cheap to install and, thanks to Power over Ethernet (PoE), can even deliver electrical power to phones, cameras and access points over the same cable that carries data.

Definition — copper media. Copper cabling transmits data by varying an electrical voltage on one or more conductors. It is limited by distance (signal loss) and by electrical noise from outside the cable and from neighbouring pairs inside it.

The signal

Electrical voltage variations on a copper pair. One differential pair carries one signal.

Where it lives

The horizontal run inside a building, from the patch panel to the wall jack. Almost every office drop is copper.

The bonus

PoE rides the same cable, so a ceiling access point or desk phone needs no mains socket.

There are three families of copper media. Learn the one-line distinction now; the two twisted-pair types are expanded in Lesson 4.

MediaOne-line description
UTP — unshielded twisted pairFour twisted pairs in an outer jacket, no extra shield; the most common LAN cabling.
STP — shielded twisted pairTwisted pairs with a foil/braid shield to resist EMI; better noise immunity, heavier and costlier.
CoaxialA single centre conductor surrounded by a mesh shield; legacy for Ethernet, now used for cable broadband and video.
Pick a copper medium · select one

Part 2

What limits copper

Copper is not perfect. Three effects cap how far and how fast a copper link can run.

Attenuation
The signal grows weaker with distance as resistance and capacitance sap energy from the line. This is the fundamental reason for a maximum cable length.
Electromagnetic interference (EMI)
External electrical fields — motors, fluorescent lights, power cables, radio transmitters — induce noise onto the copper pairs and corrupt the signal.

Crosstalk is signal from one pair coupling into a neighbouring pair inside the same cable. Twisting the pairs is the primary defence: the more twists per unit length, the more evenly the interference cancels. Crosstalk comes in three named forms, and the exam expects the terms.

TermWhat it means
NEXT (near-end crosstalk)Crosstalk measured at the same end as the transmitting pair.
FEXT (far-end crosstalk)Crosstalk measured at the far end of the cable, away from the transmitter.
Alien crosstalk (AXT)Crosstalk coupled between separate, adjacent cables in a bundle — the effect Cat6a is engineered to control.
Exam tip. If a question names a crosstalk term, match it to the measurement point: near end = the transmitting end, far end = the receiving end, alien = a neighbouring cable rather than a neighbouring pair.
Part 3

UTP categories (canonical values)

Twisted-pair copper is rated by category. The category sets the guaranteed bandwidth (in MHz), the maximum speed, and the distance at that speed. These are the canonical figures — memorise the table.

CategoryBandwidthMax speedMax distanceTypical use
Cat5e100 MHz1 Gbps100 mHome and small-office gigabit
Cat6250 MHz1 Gbps; 10 Gbps at up to ~55 m100 m (1 Gbps); ~55 m (10 Gbps)Office; short 10G runs
Cat6a500 MHz10 Gbps100 mEnterprise / data-centre 10G
Cat7600 MHz10 Gbps~100 mISO-only (Class F), fully shielded; not a TIA category
Cat82000 MHz25 / 40 Gbps~30 mData-centre switch-to-server only
Note. Cat5e is rated to 100 MHz and carries 1 Gbps the full 100 m. Cat6 doubles the bandwidth to 250 MHz and carries 1 Gbps at 100 m, but reaches 10 Gbps only to about 55 m. Cat6a doubles again to 500 MHz, adds alien-crosstalk control, and carries 10 Gbps the full 100 m. Cat7 is an ISO (Class F) standard, not a category recognised by TIA, and needs non-RJ-45 connectors (GG45/TERA) for its full rating. Cat8 is very high bandwidth but only about 30 m — it is a data-centre switch-to-server cable, not general horizontal cabling.
Exam tip. The three numbers to recall instantly: Cat5e = 100 MHz / 1 Gbps / 100 m; Cat6 = 250 MHz / 1 Gbps @ 100 m and 10 Gbps @ ~55 m; Cat6a = 500 MHz / 10 Gbps / 100 m. If a question needs 10 Gbps over a full 100 m copper channel, the answer is Cat6a.
Category decoder · select a category

Part 4

The 100 m channel rule

For Ethernet over twisted-pair copper, the maximum channel length is 100 metres (about 328 ft). This is not a round number chosen for convenience: it is the distance over which the signal can survive attenuation and still be decoded. The 100 m is divided as:

So a “100 m” run is really 90 m of installed cable plus up to 10 m of patch leads. Running copper beyond 100 m causes attenuation to win over signal and the link to fail or error — the reason fibre takes over for longer spans (Lesson 5).

Watch out. The 100 m limit is the channel total. It is the same for Cat5e, Cat6 and Cat6a at 1 Gbps — higher categories buy bandwidth (MHz) and speed headroom, not extra length. Only the 10 Gbps distance differs: ~55 m on Cat6 versus the full 100 m on Cat6a.
Channel budget · build a run and see if it fits
100 m limit
Channel 0 m Within spec

Part 5

The RJ-45 connector and the three patch cords

Twisted-pair Ethernet uses the RJ-45 plug, correctly called 8P8C (8 positions, 8 contacts). It terminates all four pairs, which is essential for Gigabit and 10G Ethernet because those standards use every pair simultaneously in both directions. The standard wiring schemes are T568A and T568B; both ends of a normal cable must use the same scheme, and in practice T568B is the most common.

Exam tip. “RJ-45” is the everyday name; the precise name is 8P8C. Remember it carries four pairs = eight wires, and that 1000BASE-T and above need all four pairs (older 10/100 Ethernet used only two).

Three wiring patterns cover every copper patch cord you will meet. Learn the one-line purpose of each; Lesson 4 covers the details and when each is used.

CableWiringConnects
Straight-throughSame pinout at both ends (pin 1→1, 2→2, and so on).Unlike devices, e.g. a PC to a switch.
CrossoverTransmit and receive pairs swapped (1↔3, 2↔6).Like devices, e.g. switch to switch or PC to PC (legacy; Auto-MDI-X now handles it).
RolloverPin order fully reversed (1↔8, 2↔7, …).A PC's serial port to a Cisco device's console port for management.
Which patch cord? · pick the scenario

Part 6

Legacy coaxial cable and the anatomy of UTP

Early Ethernet ran on coaxial cable, and the two variants are still named on exams:

Coax has been replaced by twisted pair in LANs, but it survives as the drop cable for cable broadband and for some video/CCTV runs.

outer jacket pair 1 pair 2 pair 3 pair 4 RJ-45 (8P8C) pins 1–8

A UTP cable holds four twisted pairs. Twisting keeps each pair's signal from coupling into its neighbours (crosstalk). All four pairs terminate in the eight positions of the RJ-45 (8P8C) connector, letting the cable carry Gigabit and 10G Ethernet over four pairs.

Key terms

Part 7 · Your turn

Review

Check what you have learned with these review questions.

Review · 6 questions

Sources

Sources & references

  1. TIA / ANSI. ANSI/TIA-568.2-D, Balanced Twisted-Pair Telecommunications Cabling and Components Standard (2018) — cable categories, connectors, channel length and Cat8 (2000 MHz, 30 m). tiaonline.org.
  2. IEEE. IEEE 802.3 — 802.3ab (1000BASE-T), 802.3an (10GBASE-T) and 802.3bz (2.5G/5GBASE-T). standards.ieee.org/ieee/802.3.
  3. ISO/IEC. ISO/IEC 11801-1:2017, Generic cabling for customer premises (Classes C–F/EA, including Cat7 Class F). iso.org/standard/66182.html.
  4. Cisco. CCNA (200-301) Exam Topics, Domain 1.6 (physical interfaces and cabling). cisco.com.

Target exams: CCNA 200-301 v1.1 · CyberOps Associate 200-201. Last content verification: 2026-10-11.