Week 5 · Lesson 9

Ethernet MAC Address

You met the MAC address earlier as a generic Layer-2 identifier. Now we look at it the way Ethernet actually uses it: a 48-bit value split into a manufacturer prefix and a device suffix, carried in the source and destination fields of every Ethernet frame, and used by a switch to deliver a frame to one, many, or all devices on a single link.

CCNA 200-301 Domain 1.0 Network Fundamentals Verified 2026-10-11
Learning objectives
Part 1

The 48-bit structure

An Ethernet MAC address is a 48-bit (6-byte) value that is burned into, or assigned to, every Ethernet network interface. It is the Layer-2 identifier that a switch uses to decide which port a frame should leave by. Unlike an IP address, a MAC address is flat: it has no network or host part, so it carries no routing information at all.

Definition — MAC address A 48-bit hardware address written as 12 hexadecimal digits. The first 24 bits are the OUI (Organizationally Unique Identifier), assigned to the manufacturer by the IEEE. The last 24 bits are a value the manufacturer assigns to the individual interface, making each interface’s address unique.

The split looks like this, using a real example:

PartBitsMeaningExample bytes
OUI24 (first 3 bytes)Vendor, registered with the IEEE00:1A:2B
Device ID24 (last 3 bytes)Interface serial number, set by the vendor3C:4D:5E
Whole address48One unique Ethernet interface00:1A:2B:3C:4D:5E

Because the OUI identifies the manufacturer, you can often tell which company built a network card just by reading the first three bytes. The IEEE keeps the master registry of OUIs; vendors then guarantee that no two of their interfaces share the same device ID. This is how a globally unique address is produced without any central coordinator handing out individual addresses.

Note — two bits inside the first byte The first byte also encodes two control bits. The least-significant bit is the I/G bit (Individual/Group): 0 means unicast, 1 means multicast or broadcast. The second-least-significant bit is the U/L bit (Universal/Local): 0 means a globally unique OUI address, 1 means an administrator set it locally. This is why a broadcast address like FF:FF:FF:FF:FF:FF has the I/G bit set to 1.
In this lesson · select a part to jump

Key ideas & exam traps · select one

Part 2

Hexadecimal and Cisco notation

Each byte of the address is written as two hexadecimal digits (0–9 and A–F), giving 12 hex digits in total. There are two ways you will see it:

Both forms describe the same 48 bits. The exam may give you one form and ask you to recognise the other, so practise converting between them:

# The same address, three ways
00:1A:2B:3C:4D:5E      (colon)
00-1A-2B-3C-4D-5E      (hyphen)
001a.2b3c.4d5e         (Cisco dotted)

# First 24 bits = OUI = 001a2b = 00:1A:2B
# Last  24 bits = device = 3c4d5e = 3C:4D:5E
Exam tip Count the groups: colon/hyphen notation has 6 groups of 2 hex digits; Cisco dotted notation has 3 groups of 4. Both equal 48 bits. If an option shows a MAC address with the wrong number of digits — say 5 groups or 8 groups — it is automatically wrong.
Part 3

Unicast, multicast, and broadcast

For IPv4 traffic over Ethernet there are exactly three kinds of destination MAC address, and the switch treats each differently:

TypeMeaningExample addressWho processes it
UnicastOne specific interface00:1A:2B:3C:4D:5EThe one NIC that owns that address
MulticastA group of interfaces that joined the group01:00:5E:00:00:05The NICs subscribed to that group
BroadcastEvery interface on the local linkFF:FF:FF:FF:FF:FFAll NICs on the segment
Watch out Broadcasts are confined to the local link. A router does not forward a Layer-2 broadcast from one network to another — that is precisely what makes a router define a broadcast domain. A switch, however, floods broadcasts out of all its ports (within the same VLAN), which is why an all-FF destination can reach every host on the segment.
Part 4

The IPv4 multicast range 01:00:5E

IPv4 multicast addresses (class D, 224.0.0.0–239.255.255.255) must be carried inside Ethernet frames, so a mapping rule exists. The IEEE reserved the Ethernet prefix 01:00:5E for IPv4 multicast, and the mapping copies the 23 low-order bits of the IPv4 multicast address into the 23 low-order bits of the MAC address. The result is that all IPv4 multicast MAC addresses fall inside one contiguous range:

Definition — IPv4 multicast MAC range IPv4 multicast maps to Ethernet addresses in the range 01:00:5E:00:00:00 through 01:00:5E:7F:FF:FF. The first 24 bits are the fixed prefix 01:00:5E; the remaining 23 bits come from the IPv4 multicast address.

Worked examples using well-known IPv4 multicast groups:

IPv4 multicastUseEthernet destination MAC
224.0.0.1All hosts on the subnet01:00:5E:00:00:01
224.0.0.2All routers01:00:5E:00:00:02
224.0.0.5OSPF01:00:5E:00:00:05
224.0.0.9RIPv201:00:5E:00:00:09
Exam tip Because only 23 bits are carried but the IPv4 multicast space uses 28 host bits, the mapping is not one-to-one: 32 different IPv4 multicast addresses share one Ethernet multicast MAC. Remember the two facts the exam wants: the prefix is 01:00:5E, and the range is 01:00:5E:00:00:00 – 01:00:5E:7F:FF:FF.
Reference table · select a row

Part 5

Source and destination in the frame

Every Ethernet frame header begins with two 6-byte address fields:

The source address is always an individual (unicast) address — a sender cannot be a group. The destination address may be unicast, multicast, or broadcast. So a frame with DA FF:FF:FF:FF:FF:FF still carries the sender’s own unicast address in the SA field. The figure below contrasts the two common cases: a unicast frame delivered to one host, and a broadcast frame delivered to all.

Unicast frame — one destination Broadcast frame — all hosts PC A SA 00:1A:2B:..:A1 Switch PC B PC C PC D DA = PC C MAC only port to PC C PC A SA 00:1A:2B:..:A1 Switch PC B PC C PC D DA = FF:FF:FF:FF:FF:FF flooded to every port
Left: a frame whose destination MAC belongs to PC C is forwarded by the switch only toward PC C. Right: a frame whose destination MAC is the broadcast address is flooded out every port except the one it arrived on, so all hosts receive it. In both cases the source MAC is the sender’s own unicast address.
Part 6

ARP: turning an IP into a MAC

A host knows the destination IP address it wants, but Ethernet needs a destination MAC. The bridge between the two is ARP (Address Resolution Protocol), and it works only on the local link. When a host needs the MAC for an IP on its own subnet, it sends an ARP request to the broadcast address FF:FF:FF:FF:FF:FF. Every host on the segment receives it, but only the host that owns the IP replies — with a unicast ARP reply giving its MAC. The requester caches the result in its ARP table.

Remember ARP request = broadcast (DA FF:FF:FF:FF:FF:FF, asks everyone). ARP reply = unicast (sent back to the one requester). This broadcast/unicast pair is a favourite exam detail in both directions.

When the destination IP is on a different network, the host does not ARP for the far host. It ARPs for its default gateway (the router) and puts the router’s MAC in the frame’s DA field. This is the key to understanding why MAC addresses are local.

Part 7

MAC addresses stay local

The single most important consequence of the Ethernet header is this: MAC addresses are rewritten at every router hop and never survive end to end. When the router receives a frame from your PC, it strips off that Layer-2 header, looks at the IP packet inside, chooses the next hop, and builds a brand-new frame whose SA is the router’s outbound interface and whose DA is the next-hop device’s MAC. The original source and destination MACs are gone.

This is why a MAC address is called a local address: it is meaningful only within one broadcast domain. It never crosses the router, so it can never be used to reach a device on another network. The IP addresses, by contrast, stay the same from source to destination (ignoring NAT). The table summarises the contrast:

AddressLayerScopeChanges at a router?
MAC2One local link / broadcast domainYes — rewritten each hop
IP3End to end across networksNo — constant source to destination
Exam tip If a question says “a frame arrives at a router,” the answer almost always involves the router creating a new frame with new source and destination MAC addresses. If it says “a packet arrives at a switch,” the switch only reads the existing MAC addresses and forwards the frame unchanged (at Layer 2). MAC = local and rewritten; IP = global and preserved.
Key terms

The vocabulary you need

Every term below appears in the lesson text above. Select one to read its definition, then use the quiz at the end to check what stuck.

Key terms · select a term

Part 8 · Your turn

Review

Check what you have learned with these review questions.

Review · 6 questions

Sources

Sources & references

  1. Cisco. CCNA (200-301) Exam Topics. cisco.com.
  2. IETF. Request for Comments (RFCs). rfc-editor.org.
  3. IANA. Internet Assigned Numbers Authority registries. iana.org.

Target exams: CCNA 200-301 v1.1 · CyberOps Associate 200-201. Last content verification: 2026-10-11.