Ethernet MAC Address
You met the MAC address earlier as a generic Layer-2 identifier. Now we look at it the way Ethernet actually uses it: a 48-bit value split into a manufacturer prefix and a device suffix, carried in the source and destination fields of every Ethernet frame, and used by a switch to deliver a frame to one, many, or all devices on a single link.
- Break a 48-bit MAC address into its OUI (24-bit vendor) and device (24-bit) halves.
- Read and write MAC addresses in hexadecimal and in Cisco dotted notation.
- Distinguish unicast, multicast, and broadcast MAC addresses as Ethernet uses them for IPv4.
- State the IPv4 multicast mapping range 01:00:5E:00:00:00 – 01:00:5E:7F:FF:FF.
- Explain how the Ethernet header's DA and SA fields are filled.
- Explain why MAC addresses never cross a router.
The 48-bit structure
An Ethernet MAC address is a 48-bit (6-byte) value that is burned into, or assigned to, every Ethernet network interface. It is the Layer-2 identifier that a switch uses to decide which port a frame should leave by. Unlike an IP address, a MAC address is flat: it has no network or host part, so it carries no routing information at all.
The split looks like this, using a real example:
| Part | Bits | Meaning | Example bytes |
|---|---|---|---|
| OUI | 24 (first 3 bytes) | Vendor, registered with the IEEE | 00:1A:2B |
| Device ID | 24 (last 3 bytes) | Interface serial number, set by the vendor | 3C:4D:5E |
| Whole address | 48 | One unique Ethernet interface | 00:1A:2B:3C:4D:5E |
Because the OUI identifies the manufacturer, you can often tell which company built a network card just by reading the first three bytes. The IEEE keeps the master registry of OUIs; vendors then guarantee that no two of their interfaces share the same device ID. This is how a globally unique address is produced without any central coordinator handing out individual addresses.
0 means unicast, 1 means
multicast or broadcast. The second-least-significant bit is the U/L bit
(Universal/Local): 0 means a globally unique OUI address, 1 means an
administrator set it locally. This is why a broadcast address like FF:FF:FF:FF:FF:FF
has the I/G bit set to 1.
Hexadecimal and Cisco notation
Each byte of the address is written as two hexadecimal digits (0–9 and A–F), giving 12 hex digits in total. There are two ways you will see it:
- Colon or hyphen notation — the form most hosts and tools show:
00:1A:2B:3C:4D:5Eor00-1A-2B-3C-4D-5E. Each pair is one byte. - Cisco dotted notation — three groups of four hex digits, used by many
Cisco IOS commands:
001a.2b3c.4d5e. The dots fall inside the vendor and device halves, not on byte boundaries.
Both forms describe the same 48 bits. The exam may give you one form and ask you to recognise the other, so practise converting between them:
# The same address, three ways
00:1A:2B:3C:4D:5E (colon)
00-1A-2B-3C-4D-5E (hyphen)
001a.2b3c.4d5e (Cisco dotted)
# First 24 bits = OUI = 001a2b = 00:1A:2B
# Last 24 bits = device = 3c4d5e = 3C:4D:5E
Unicast, multicast, and broadcast
For IPv4 traffic over Ethernet there are exactly three kinds of destination MAC address, and the switch treats each differently:
| Type | Meaning | Example address | Who processes it |
|---|---|---|---|
| Unicast | One specific interface | 00:1A:2B:3C:4D:5E | The one NIC that owns that address |
| Multicast | A group of interfaces that joined the group | 01:00:5E:00:00:05 | The NICs subscribed to that group |
| Broadcast | Every interface on the local link | FF:FF:FF:FF:FF:FF | All NICs on the segment |
- A unicast address has the I/G bit set to 0 and names exactly one device. A frame sent to a unicast address is meant for that one NIC.
- A multicast address has the I/G bit set to 1 and identifies a group.
Only devices that have asked to receive that group (for example, via IGMP) process the frame;
everyone else ignores it. For IPv4, the multicast MAC begins with
01:00:5E. - A broadcast address is the special multicast
FF:FF:FF:FF:FF:FF(all 48 bits set). It targets every device on the local network segment, and every NIC must process it. For IPv4, a frame addressed toFF:FF:FF:FF:FF:FFis the Layer-2 form of the IPv4 broadcast255.255.255.255.
FF destination can reach every host
on the segment.
The IPv4 multicast range 01:00:5E
IPv4 multicast addresses (class D, 224.0.0.0–239.255.255.255) must be carried inside Ethernet frames, so a mapping rule exists. The IEEE reserved the Ethernet prefix 01:00:5E for IPv4 multicast, and the mapping copies the 23 low-order bits of the IPv4 multicast address into the 23 low-order bits of the MAC address. The result is that all IPv4 multicast MAC addresses fall inside one contiguous range:
01:00:5E:00:00:00 through 01:00:5E:7F:FF:FF.
The first 24 bits are the fixed prefix 01:00:5E; the remaining 23 bits come from the
IPv4 multicast address.
Worked examples using well-known IPv4 multicast groups:
| IPv4 multicast | Use | Ethernet destination MAC |
|---|---|---|
224.0.0.1 | All hosts on the subnet | 01:00:5E:00:00:01 |
224.0.0.2 | All routers | 01:00:5E:00:00:02 |
224.0.0.5 | OSPF | 01:00:5E:00:00:05 |
224.0.0.9 | RIPv2 | 01:00:5E:00:00:09 |
01:00:5E, and the range is
01:00:5E:00:00:00 – 01:00:5E:7F:FF:FF.
Source and destination in the frame
Every Ethernet frame header begins with two 6-byte address fields:
- Destination MAC (DA) — whom the frame is for. A switch reads this field to decide where to forward.
- Source MAC (SA) — who sent it. A switch reads this field to learn which port that device is reachable through (Lesson 10).
The source address is always an individual (unicast) address — a sender
cannot be a group. The destination address may be unicast, multicast, or broadcast.
So a frame with DA FF:FF:FF:FF:FF:FF still carries the sender’s own unicast
address in the SA field. The figure below contrasts the two common cases: a unicast frame delivered
to one host, and a broadcast frame delivered to all.
ARP: turning an IP into a MAC
A host knows the destination IP address it wants, but Ethernet needs a destination MAC. The bridge between the two is ARP (Address Resolution Protocol), and it works only on the local link. When a host needs the MAC for an IP on its own subnet, it sends an ARP request to the broadcast address FF:FF:FF:FF:FF:FF. Every host on the segment receives it, but only the host that owns the IP replies — with a unicast ARP reply giving its MAC. The requester caches the result in its ARP table.
FF:FF:FF:FF:FF:FF, asks everyone).
ARP reply = unicast (sent back to the one requester). This broadcast/unicast pair
is a favourite exam detail in both directions.
When the destination IP is on a different network, the host does not ARP for the far host. It ARPs for its default gateway (the router) and puts the router’s MAC in the frame’s DA field. This is the key to understanding why MAC addresses are local.
MAC addresses stay local
The single most important consequence of the Ethernet header is this: MAC addresses are rewritten at every router hop and never survive end to end. When the router receives a frame from your PC, it strips off that Layer-2 header, looks at the IP packet inside, chooses the next hop, and builds a brand-new frame whose SA is the router’s outbound interface and whose DA is the next-hop device’s MAC. The original source and destination MACs are gone.
This is why a MAC address is called a local address: it is meaningful only within one broadcast domain. It never crosses the router, so it can never be used to reach a device on another network. The IP addresses, by contrast, stay the same from source to destination (ignoring NAT). The table summarises the contrast:
| Address | Layer | Scope | Changes at a router? |
|---|---|---|---|
| MAC | 2 | One local link / broadcast domain | Yes — rewritten each hop |
| IP | 3 | End to end across networks | No — constant source to destination |
The vocabulary you need
Every term below appears in the lesson text above. Select one to read its definition, then use the quiz at the end to check what stuck.
Review
Check what you have learned with these review questions.
Sources & references
- Cisco. CCNA (200-301) Exam Topics. cisco.com.
- IETF. Request for Comments (RFCs). rfc-editor.org.
- IANA. Internet Assigned Numbers Authority registries. iana.org.
Target exams: CCNA 200-301 v1.1 · CyberOps Associate 200-201. Last content verification: 2026-10-11.