Week 5 · Lesson 11

How the Switch Processes Frames

We have covered the MAC address and the MAC address table. Now we put them together and follow a single frame from the instant it arrives on a port to the instant it leaves. This is the switch’s core algorithm — learn, look up, forward — and it is also where the switching modes (store-and-forward, cut-through, fragment-free) change what happens.

CCNA 200-301 Domain 1.0 Network Fundamentals Verified 2026-10-11
Learning objectives
Part 1

The six processing steps

Every frame that enters a switch port goes through the same sequence. Learn these six steps as a pipeline; almost every switch question is a question about one of them.

  1. Receive the frame. The frame arrives on the ingress port. The switch buffers or inspects it according to its switching mode (see below).
  2. Check the FCS. The switch recalculates the checksum and compares it with the Frame Check Sequence in the trailer. If the frame is corrupt, it is discarded — it is never forwarded.
  3. Learn the source MAC. The switch reads the source address and records that MAC is reachable out of the ingress port, adding or updating the MAC address table.
  4. Look up the destination MAC. The switch searches the table for the destination address.
  5. Forward, flood, or filter. Known unicast → forward out one port; unknown unicast / broadcast / multicast → flood out all other ports; destination on the ingress port → filter (drop).
  6. Update the aging timer. The entry for the source MAC has its age reset, so the switch remembers the address as long as the device keeps talking.
Exam tip The order matters: the switch learns before it decides. If a frame comes in and the destination is the same port it arrived on, the switch still learns the source first, then filters. And a corrupt frame is dropped at step 2 — it never affects the table and is never forwarded.
A frame arrives on Gi0/1 and the switch runs its pipeline Switch 1 receive 2 FCS 3 learn 4 lookup 5 forward 6 age PC A SA = A, DA = D PC B PC D PC C Gi0/2 Gi0/3 Gi0/4 DA = D is known → forward out Gi0/3 only Learned from source MAC SA = A → Gi0/1 SA = D → Gi0/3 (B and C unknown → flooded)
One frame runs the whole pipeline. The switch learns PC A from the source address (Gi0/1) and forwards the frame to PC D because its destination MAC is known on Gi0/3. Hosts B and C are not involved at all.
In this lesson · select a part to jump

Key ideas & exam traps · select one

Part 2

Step 2: the FCS check

The FCS (Frame Check Sequence) is a checksum in the Ethernet trailer, computed by the sender over the whole frame. The receiver recomputes it and compares. If the two do not match, the frame was corrupted somewhere on the link — by noise, a bad cable, a duplex mismatch, or a collision. A switch configured for store-and-forward will discard such a frame. The FCS only detects errors; it does not correct them, and the Data Link layer does not retransmit. (Detecting a problem and dropping the frame is usually enough, because TCP above will retransmit if it matters.)

Part 3

Forward, flood, or filter

Once the destination MAC has been looked up, exactly one of three things happens:

DestinationTable resultSwitch action
Known unicastFound, on a different portForward out that one port
Known unicastFound, on the ingress portFilter — drop, do not forward
Unknown unicastNot foundFlood out all other ports
Broadcast / multicastGroup addressFlood out all other ports (unless IGMP snooping applies)
Definition — filtering Filtering is the switch dropping a frame because the destination is on the same port the frame arrived on. There is no point sending it back out the port it came from, so the frame is discarded rather than forwarded.
Reference table · select a row

Part 4

Switching modes

The switch’s frame-forwarding method decides how much of a frame it must read before it starts sending. There are three modes, and the exam tests their trade-offs:

ModeWhat it doesStrengthWeakness
Store-and-forward Buffers the entire frame, computes and checks the FCS, and forwards only if the frame is valid. Most reliable; discards corrupt frames, runts, and giants before they spread. Highest latency, because it must wait for the whole frame.
Cut-through Starts forwarding as soon as it has read the destination MAC (the first 6 bytes after the preamble), without checking the FCS. Lowest latency, independent of frame size. Propagates bad frames — runts and corrupt frames are forwarded onward.
Fragment-free Reads the first 64 bytes before forwarding (also called modified cut-through). Filters out most collision fragments, which occur within the first 64 bytes. Latency between the other two; it can still forward some errors.
Exam tip Remember the sized details: cut-through starts after the destination MAC; fragment-free waits for the first 64 bytes; store-and-forward waits for the whole frame and the FCS. 64 bytes is the Ethernet minimum frame size — the same number a runt falls below. Store-and-forward is the most reliable and the most common default on modern Cisco switches.
Part 5

Latency and what each mode costs

Latency is the delay a frame experiences crossing the switch. The switching mode sets a floor for it:

This is the central trade-off: reliability versus latency. Cut-through buys speed by giving up error checking; store-and-forward buys correctness by waiting. Modern switches are fast enough that store-and-forward is the usual choice, but the concept is a common exam item.

Part 6

Collision and broadcast domains

Two domain concepts explain why switches replaced hubs:

Note A switch increases the number of collision domains (one per port) but leaves the broadcast domain unchanged. A router (or a VLAN boundary) separates broadcast domains. Learn these two verbs as a pair.
Part 7

Transparent to IP

A switch is called transparent because it does not alter the Layer-3 content of the traffic passing through it. It reads only the Ethernet header, then forwards the frame unchanged — same source MAC, same destination MAC, same IP packet inside. It does not modify the IP addresses, does not decrement a TTL, and needs no IP configuration to do its job. The hosts and routers on either side behave as if the switch were invisible, which is exactly what “transparent bridging” (IEEE 802.1D) means. This is the crucial contrast with a router, which is very much not transparent: a router rewrites the Layer-2 header at every hop and makes decisions using the Layer-3 addresses.

BehaviourSwitch (Layer 2)Router (Layer 3)
Decision based onDestination MACDestination IP
Modifies frame?No — forwards unchangedYes — builds a new frame each hop
Breaks collision domains?Yes (one per port)Yes
Breaks broadcast domains?NoYes
Part 8

Exam scenario

The question. A PC sends a unicast frame to a server on the same VLAN. Before any other host has spoken, the switch has only one entry in its MAC address table: the server, on Gi0/20. The PC is on Gi0/1. A technician sees the frame leave every port except Gi0/1. Why did the switch flood a frame that was clearly destined for the server?

The answer. Look carefully at the table: the entry the switch has is the server, and the newly arrived frame is from the PC to the server. The switch learns the PC’s source address (adding “PC → Gi0/1”), then looks up the destination. Here is the trap: a switch forwards a frame as a known unicast only if the destination MAC is already in the table. If the server entry was for a different VLAN or had aged out, the destination is unknown, so the switch floods it out of all ports except the ingress port. Once the server replies and the switch has both addresses, later frames are forwarded to the single correct port. This is the classic unknown unicast flooding behaviour, and it is normal and expected — a switch never drops an unknown frame on an access port; it floods it to be safe.

Watch out The statement “it flooded because the destination was a broadcast” is the distractor. Broadcast floods, yes — but so does an unknown unicast. Read the addresses in the question: if the destination is a real unicast address that is simply absent from the table, the answer is still flooding, and the reason is unknown unicast.
Key terms

The vocabulary you need

Every term below appears in the lesson text above. Select one to read its definition, then use the quiz at the end to check what stuck.

Key terms · select a term

Part 9 · Your turn

Review

Check what you have learned with these review questions.

Review · 6 questions

Sources

Sources & references

  1. Cisco. CCNA (200-301) Exam Topics. cisco.com.
  2. IETF. Request for Comments (RFCs). rfc-editor.org.
  3. IANA. Internet Assigned Numbers Authority registries. iana.org.

Target exams: CCNA 200-301 v1.1 · CyberOps Associate 200-201. Last content verification: 2026-10-11.