Week 5 · Lesson 17

EtherChannel and LACP

Two links between the same pair of switches look like two paths — and that is exactly why STP (Lesson 18) will block one of them. EtherChannel is the answer to the paradox: bundle the links into one logical pipe so the pair becomes a single, loop-free, higher-bandwidth connection. This lesson covers the bundle, the negotiation protocols (LACP and PAgP), and the joins rules that make or break it.

CCNA 200-301 Domain 2.0 Network Access Verified 2026-10-11
Learning objectives
Part 1

The loop problem, again

Plumb two cables between two switches and you have created a Layer 2 loop. Frames will circulate forever, the MAC table will flap, and a broadcast storm will saturate both links — unless Spanning Tree Protocol (STP) acts. STP will do its job and place one of the two ports in the blocking state, which means your second “redundant” cable silently carries no traffic. You paid for a 2 Gbit/s bundle and got a hot standby instead.

EtherChannel is the mitigation: it makes the two links logically one before STP ever counts paths. The channel is a single logical link, the loop disappears, STP sees one interface, and both physical links pass traffic. Throughput rises, fault tolerance improves (one member can die and the bundle keeps carrying traffic), and STP is never forced to kill the spare.

Definition — EtherChannel EtherChannel (also called port-channel) groups two to eight physical ports into one logical link between two directly connected devices. The members are treated as a single interface by STP and by configuration, and frames are distributed across them by a load-balancing algorithm.
In this lesson · select a part to jump

Key ideas & exam traps · select one

Part 2

What EtherChannel is

Configuring an EtherChannel means: (a) choosing the member ports, (b) choosing how the channel is formed — statically or with a negotiation protocol — and (c) applying the same interface settings to every member. The result appears in the configuration and in show etherchannel summary as a channel-group (e.g. Port-channel 1) with member ports beneath it. The diameters of the individual links may differ by speed, but all members must be operating in a compatible way or the channel silently refuses to form.

Switch S1 Switch S2 Gi0/1 Gi0/2 Port-channel 1 — one logical link, two physical members
Two switched links bundled by EtherChannel become one logical link. STP sees a single interface, so nothing is blocked, and both cables carry traffic.
Part 3

LACP: active and passive

Link Aggregation Control Protocol (LACP) is the open standard, defined in IEEE 802.3ad (now part of 802.1AX) and supported by virtually every vendor. LACP speaks two modes, and the exam tests the pairing matrix relentlessly:

The command is channel-group <n> mode active. Because LACP is vendor-neutral, it is the right answer whenever the two ends are different brands. The canonical rule: active forms with active or passive; two passive ports never form a channel.

Exam tip The mode pair matrix is standard material. LACP: active with active works, active with passive works, passive with passive does not. PAgP mirrors it: desirable with desirable works, desirable with auto works, auto with auto does not. Learn the one broken pairing per protocol and you have the whole grid.
Part 4

PAgP: the Cisco alternative

Port Aggregation Protocol (PAgP) is Cisco’s proprietary negotiation protocol for EtherChannel. Its two modes are desirable and auto — the direct ancestors of DTP’s modes and easy to confuse with them. PAgP desirable actively negotiates; auto waits. The same matrix applies: desirable pairs with either, auto pairs only with desirable. Unlike LACP, PAgP understands only Cisco equipment, so on a Cisco-to-Cisco link it works perfectly and on anything else it is useless.

Part 5

Static on and when to use it

The third formation mode, on, skips negotiation entirely:

S1(config)# interface range gigabitethernet 0/1-2
S1(config-if-range)# channel-group 1 mode on

“On” says: I am a member, no questions asked. No LACP, no PAgP — both sides simply bundle. The danger is that a mismatched or half-connected port gets silently absorbed into the channel instead of being rejected by negotiation, so network engineers prefer LACP where a negotiation check is useful and use on mainly for links to devices that do not speak either protocol (or in labs where the topology is fixed and known). For the exam, remember that on is not a PAgP or LACP mode — it is the no-protocol option.

Part 6

The bundling requirements

Membership is a strict checklist. If any member deviates, the whole member is refused and the bundle degrades (or fails). The canonical requirements, which the exam lists and asks you to spot:

Watch out A mismatch in any requirement does not form a “slow channel” — it forms no channel at all for that port. The classic exam scenario: two ports bundled, one in VLAN 10 and one in VLAN 20, and the bundle never comes up. The fix is to make the VLAN settings identical, not to restart the switch.
Part 7

Configuration example

Configure both ends identically. The recommended practice is to set the physical properties first, then bundle, then apply the channel configuration to the logical port-channel interface so the members inherit it:

S1(config)# interface range gigabitethernet 0/1-2
S1(config-if-range)# switchport mode trunk
S1(config-if-range)# switchport trunk allowed vlan 10,20
S1(config-if-range)# channel-group 1 mode active   ! LACP active
S1(config-if-range)# exit

S1(config)# interface port-channel 1
S1(config-if)# switchport mode trunk
S1(config-if)# switchport trunk allowed vlan 10,20
S1(config-if)# end

S2(config)# interface range gigabitethernet 0/1-2
S2(config-if-range)# switchport mode trunk
S2(config-if-range)# channel-group 1 mode active   ! LACP active on the far end
S2(config-if-range)# end

Both ends mode active → the channel forms. Had S2 used mode passive it would still form (active+passive works); had it used PAgP or on while S1 was active, the two would never agree, because LACP and PAgP frames are mutually unintelligible. One end must want the same protocol as the other.

Part 8

Load balancing

EtherChannel does not split a single flow across members — that would reorder frames and break TCP. Instead, a hash picks a member for each “flow” based on header fields, and all frames of that flow follow the same link. The default hash for Layer 2 switching is typically source and destination MAC; for routed traffic it can include IP addresses and ports. The consequence matters on the exam: a channel between two hosts produces one hash value, so that particular conversation uses only one member — which is why “the load split evenly across all links” is a false statement. Change the distribution method with port-channel load-balance <method>.

The number of members follows a power-of-two logic: 2, 4, or 8 ports on most platforms (up to 16 on some newer hardware, with 8 active). The hash buckets align to the number of active members, so a 3-member channel is effectively treated as 4 buckets.

Part 9

Verification

S1# show etherchannel summary
Flags:  D - down        P - bundled in port-channel
        I - stand-alone s - suspended   H - Hot-standby
Group  Port-channel  Protocol    Ports
------+-------------+-----------+-----------------------------------------------
1      Po1(SU)         LACP      Gi0/1(P)   Gi0/2(P)

S1# show port-channel 1
                        Channel group: 1
Channel members: 2
                          GigabitEthernet0/1
                          GigabitEthernet0/2
Load-balance method: src-dst mac

Read the flags column: P marks a member successfully bundled into the channel. (SU) after the bundle name means the logical interface is up and in use. If a port shows I (stand-alone) instead of P, it failed a consistency check — verify speed, duplex, VLAN, and trunk state before anything else.

ProtocolStandardModesChannel-group command
LACPIEEE 802.3ad / 802.1AX (open)active, passivechannel-group <n> mode active
PAgPCisco proprietarydesirable, autochannel-group <n> mode desirable
OnNone (static)—channel-group <n> mode on
Reference table · select a row

Key terms

The vocabulary you need

Every term below appears in the lesson text above. Select one to read its definition, then use the quiz at the end to check what stuck.

Key terms · select a term

Part 10 · Your turn

Review

Check what you have learned with these review questions.

Review · 5 questions

Sources

Sources & references

  1. Cisco. CCNA (200-301) Exam Topics. cisco.com.
  2. IETF. Request for Comments (RFCs). rfc-editor.org.
  3. IANA. Internet Assigned Numbers Authority registries. iana.org.

Target exams: CCNA 200-301 v1.1 · CyberOps Associate 200-201. Last content verification: 2026-10-11.