Network Fundamentals — Question Bank
Thirty-six exam-style multiple-choice questions covering CCNA Domain 1.0 (Network Fundamentals, 15% of the exam): components, topologies, cabling, interfaces, TCP/UDP, IPv4 and IPv6 addressing, wireless principles, virtualization, and switching concepts. Answer each question to get instant feedback and a full explanation.
- Work one part at a time; each part is a separate self-scoring quiz.
- Read the explanation after every answer — the distractor analysis is where the learning is.
- Reset a quiz with the button at its foot to try it again cold.
- Your answers are saved on this device (local storage), so you can leave and return.
Part 1 — Components & topologies
Choose the single best answer. Feedback and an explanation appear immediately.
-
Which device forwards frames within a single LAN using MAC addresses?
- Router
- Firewall
- Switch
- Modem
A Layer 2 switch builds a MAC address table and forwards frames inside one broadcast domain. A router (Layer 3) moves packets between networks; a firewall filters traffic; a modem converts the signal to the service provider medium.
-
Which device forwards packets between different IP networks?
- Layer 2 switch
- Router
- Access point
- Hub
Routers make forwarding decisions using the destination IP address and a routing table, connecting separate subnets. Switches, hubs, and access points stay within one Layer 2 domain.
-
Which device lets wireless clients join a wired LAN?
- Router
- Switch
- Load balancer
- Wireless access point
A wireless access point (WAP) bridges 802.11 radio clients to the wired distribution system. In most small networks it is integrated into a wireless router.
-
A small office wants the cheapest possible fault tolerance in its core. Which physical topology connects every device to every other device?
- Full mesh
- Star
- Bus
- Ring
A full mesh gives maximum redundancy with no single point of failure, but cabling and port cost grows quickly. A star is cheap and common but depends on the central device. A bus is a shared backbone; a ring passes traffic node to node.
-
In a three-tier campus design, which layer provides high-speed switching and aggregates distribution switches?
- Access layer
- Distribution layer
- Core layer
- Edge layer
The core is the high-speed backbone that aggregates distribution switches. The distribution layer controls policy and routing between access and core; the access layer connects end devices.
-
Which two-tier design collapses the core and distribution into a single layer for smaller campuses?
- Hub-and-spoke
- Collapsed core
- Spine-and-leaf
- Full mesh
A collapsed-core (two-tier) design merges core and distribution where the campus is small enough that a dedicated backbone is unnecessary. Spine-and-leaf is a data-centre design.
-
Which device is always an intermediary device rather than an end host?
- Layer 3 switch
- IP phone
- Laptop
- Network printer
Intermediary devices forward traffic rather than originate it: switches, routers, firewalls, and access points. Phones, laptops, and printers are end hosts even though they have IP addresses.
-
Which describes a WAN link rather than a LAN?
- Connects devices inside one building
- Owned and managed by one organisation
- High bandwidth at low cost per port
- Connects geographically separate sites over a provider network
A WAN spans large geographic areas and is typically leased from a service provider. LANs are local, usually owned by one organisation, and offer high bandwidth per port at low cost.
Part 2 — Cabling, interfaces & wireless
-
Which cable type carries data to a device and also supplies power over the same cable pair set?
- Fibre-optic
- Ethernet supporting Power over Ethernet (PoE)
- Coaxial
- Console (rollover)
PoE delivers DC power and data over the same twisted-pair Ethernet cable to devices such as IP phones, cameras, and access points. Fibre carries light, coaxial is legacy, and a rollover cable is for management only.
-
Which copper Ethernet standard is rated for 1 Gbps over 100 m of Category 5e or better cable?
- 10BASE-T
- 100BASE-TX
- 1000BASE-T
- 10GBASE-T
1000BASE-T (Gigabit Ethernet over twisted pair) reaches 100 m on Cat 5e/6. 100BASE-TX is Fast Ethernet at 100 Mbps; 10GBASE-T needs Cat 6a for 100 m.
-
Which cable would you use to connect two like devices (switch to switch) directly, if the ports do not support auto-MDI/MDIX?
- Crossover cable
- Straight-through cable
- Rollover cable
- Twinaxial cable
A crossover cable swaps transmit and receive pairs and historically linked like devices. Straight-through links dissimilar devices; rollover is for console management. Modern ports auto-detect (auto-MDI/MDIX).
-
You can ping the default gateway but cannot reach a host on a remote subnet, and the local link light is on. What is the most likely Layer 1/2 cause on the local interface?
- Wrong default gateway
- Duplicate IP address
- Incorrect DNS server
- Speed/duplex mismatch on the uplink
A speed or duplex mismatch is a classic interface issue that produces errors and poor throughput while the link stays up. Gateway and DNS problems would show different symptoms.
-
Which fibre type is best for long distances (kilometres) in a campus backbone?
- Multimode fibre
- Single-mode fibre
- Cat 6a UTP
- Coaxial
Single-mode fibre has a tiny core and carries laser light for many kilometres. Multimode is cheaper and used for shorter runs inside a building; copper is limited to about 100 m.
-
Which three 2.4 GHz channels are non-overlapping in North America?
- 1, 2, 3
- 2, 5, 9
- 1, 6, 11
- 3, 6, 9
In the 2.4 GHz band the only non-overlapping channels are 1, 6, and 11. Other combinations overlap and cause co-channel interference.
-
A wireless client shows a strong signal but low throughput in a crowded office. Which is the most likely cause?
- Co-channel interference from neighbouring APs
- Wrong subnet mask
- Duplex mismatch on the WLAN
- Incorrect default gateway
The unlicensed 2.4 GHz band is crowded. Overlapping channels and many clients share airtime, so signal strength can be high while actual throughput is poor. Wireless uses CSMA/CA, not duplex settings.
-
Which interface on a Cisco switch is used for out-of-band management with a console cable?
- Gi0/1
- VLAN 1 SVI
- USB storage port
- Console port
Out-of-band management uses the physical console (or auxiliary) port even when the network is down. The switch virtual interface (SVI) and Gigabit ports are in-band, requiring a working network.
Part 3 — TCP, UDP & models
-
Which transport protocol is connection-oriented and guarantees delivery through acknowledgements and retransmission?
- UDP
- TCP
- ICMP
- ARP
TCP performs a three-way handshake, uses sequence numbers, and retransmits lost segments. UDP is connectionless best-effort; ICMP and ARP are not transport protocols.
-
A live voice stream must avoid the delay that retransmission causes. Which transport protocol should carry it?
- UDP
- TCP
- SCTP
- DCCP
Real-time voice and video use UDP because low latency matters more than perfect delivery. Retransmitting a lost voice packet is pointless once the moment has passed.
-
Which PDU is created at the transport layer when the protocol in use is UDP?
- Frame
- Packet
- Datagram
- Bit
A UDP transport-layer unit is a datagram; a TCP unit is a segment. Packets are Layer 3 and frames are Layer 2.
-
Which statement about the TCP/IP model is correct?
- It has seven layers, exactly matching OSI.
- Its Network Access layer maps only to OSI Layer 1.
- Its Application layer maps only to OSI Layer 7.
- Its Application layer maps to OSI Layers 5, 6 and 7.
The four-layer TCP/IP model folds OSI Session, Presentation, and Application into one Application layer, and OSI Data Link and Physical into Network Access.
-
Which field in the TCP/UDP header identifies the receiving application on the destination host?
- Source IP address
- Destination port number
- Sequence number
- Window size
Port numbers identify applications. The destination port tells the receiving host which service should handle the data; the source port lets the reply return to the right session.
-
Which statement best describes a socket?
- The combination of an IP address and a port number
- The MAC address of the NIC
- The default gateway of a host
- A physical RJ-45 connector
A socket is an IP address paired with a port number, for example 192.168.1.10:443. It uniquely identifies an application endpoint on a host.
Part 4 — IPv4 addressing & subnetting
-
How many usable host addresses are there in a /26 subnet?
- 64
- 32
- 62
- 30
A /26 leaves 6 host bits. 26 = 64 total addresses; subtract the network and broadcast addresses to get 62 usable hosts.
-
Which private IPv4 range is defined by RFC 1918 as a /12?
- 172.16.0.0 – 172.31.255.255
- 10.0.0.0 – 10.255.255.255
- 192.168.0.0 – 192.168.255.255
- 169.254.0.0 – 169.254.255.255
RFC 1918 defines 10.0.0.0/8, 172.16.0.0/12 (172.16.0.0 to 172.31.255.255), and 192.168.0.0/16. 169.254.0.0/16 is the APIPA link-local range, not RFC 1918.
-
A host that cannot reach a DHCP server may self-assign an address from which range?
- 10.0.0.0/8
- 169.254.0.0/16
- 100.64.0.0/10
- 224.0.0.0/4
APIPA (Automatic Private IP Addressing) uses 169.254.0.0/16 when no DHCP server answers. Seeing this address is a strong clue that DHCP failed.
-
What is the broadcast address of the subnet 192.168.10.64/27?
- 192.168.10.63
- 192.168.10.64
- 192.168.10.127
- 192.168.10.95
A /27 has a block size of 32. The subnet starts at .64, so it spans .64 to .95; the broadcast is the last address, .95, and the network address is .64.
-
Which classful class does the address 172.20.5.10 belong to, and what is its default mask?
- Class A, 255.0.0.0
- Class C, 255.255.255.0
- Class B, 255.255.0.0
- Class D, not applicable
First octets 128–191 are Class B with a default /16 mask (255.255.0.0). Class A is 1–126, Class C is 192–223, and Class D (224–239) is multicast.
-
Which address is the directed broadcast for the network 10.1.1.0 255.255.255.128?
- 10.1.1.127
- 10.1.1.128
- 10.1.1.255
- 10.1.1.0
255.255.255.128 is a /25 with a block size of 128. The subnet runs 10.1.1.0 to 10.1.1.127, so the broadcast is 10.1.1.127. The next subnet begins at .128.
-
Which subnet mask supports exactly 2 usable host addresses?
- /29
- /30
- /31
- /28
A /30 leaves 2 host bits: 22 − 2 = 2 usable addresses, ideal for point-to-point links. A /29 gives 6 and a /31 has no broadcast/network convention in older designs.
-
Which address is a valid host in the subnet 192.168.5.32/27?
- 192.168.5.32
- 192.168.5.63
- 192.168.5.64
- 192.168.5.40
The /27 subnet runs 192.168.5.32 to 192.168.5.63. .32 is the network address and .63 the broadcast, so neither is usable. .64 starts the next subnet. .40 is a valid host inside the range.
Part 5 — IPv6 & virtualization
-
How many bits are in an IPv6 address?
- 64
- 128
- 32
- 256
IPv6 uses 128 bits, written as eight groups of four hexadecimal digits. That is four times the 32 bits of IPv4.
-
Which range is the IPv6 global unicast address space?
- FE80::/10
- FC00::/7
- 2000::/3
- FF00::/8
Global unicast addresses begin with 2000::/3 (first three bits 001). FE80::/10 is link-local, FC00::/7 unique local, and FF00::/8 multicast.
-
Which IPv6 address type is automatically created on every interface and used only on the local link?
- Link-local (FE80::/10)
- Global unicast (2000::/3)
- Unique local (FC00::/7)
- Multicast (FF00::/8)
Every IPv6 interface forms a link-local address (FE80::/10) even without a router, and neighbours use it for on-link communication such as NDP.
-
In the address 2001:0db8:0000:0000:0000:0000:1428:57ab, which is the correctly compressed form?
- 2001:db8::0000:1428:57ab
- 2001:db8:0:0:0:0:1428::57ab
- 2001:0db8::1428:57ab:0
- 2001:db8::1428:57ab
Leading zeros in each group are dropped, and one run of all-zero groups is replaced by a single "::". The double colon may appear only once, which eliminates A, B, and C.
-
Which statement about IPv6 addressing is true?
- IPv6 uses broadcast addresses.
- IPv6 uses multicast and anycast instead of broadcast.
- IPv6 addresses are shown in decimal.
- IPv6 has a 64-bit address space.
IPv6 replaces broadcast with multicast (and anycast) and is written in hex. The solicit-node multicast address, for example, reaches all nodes on a link.
-
Which technology allows one physical server to host several isolated virtual machines?
- Port Address Translation
- Link aggregation
- Server virtualization (hypervisor)
- Spanning Tree Protocol
A hypervisor runs multiple virtual machines on one physical host, each with its own OS and resources. This improves hardware utilisation and simplifies provisioning.
Missed-question review map
If you miss a question, use this table to find the lesson that covers it.
| Part | Topic | Where it is covered |
|---|---|---|
| Part 1 | Devices, roles, topologies, LAN vs WAN | Week 1 · 01–02; Week 2 · 01 |
| Part 2 | Cabling, PoE, fibre, channels, interface issues | Week 4 · Physical Layer lessons; Week 8 · Wireless |
| Part 3 | TCP/UDP, ports, sockets, TCP/IP model | Week 3 · 03–05; Week 8 · Transport Layer |
| Part 4 | IPv4 classes, private ranges, host maths | Week 1 · 04–07; Week 7 · Subnetting |
| Part 5 | IPv6 addressing and types, virtualization | Week 6 · Network Layer; Week 11 · Servers |
Sources & references
- Cisco. CCNA (200-301) Exam Topics, Domain 1.0 Network Fundamentals. cisco.com.
- Rekhter, Y. et al. RFC 1918: Address Allocation for Private Internets (1996). rfc-editor.org/rfc/rfc1918.
- Hinden, R. & Deering, S. RFC 4291: IP Version 6 Addressing Architecture (2006). rfc-editor.org/rfc/rfc4291.
- Postel, J. RFC 791: Internet Protocol (1981). rfc-editor.org/rfc/rfc791.
- IEEE. IEEE 802.11 Wireless LAN Standards. standards.ieee.org.
Target exams: CCNA 200-301 v1.1 · CyberOps Associate 200-201. Last content verification: 2026-10-11.