Week 4 · Lesson 6

Wireless Media

The fourth network medium is not a cable at all — it is radio. Wireless lets hosts join a network with no tether, but it trades reliability and consistency for that freedom. This lesson covers the radio bands, channels and interference, the 802.11 standards with their theoretical speeds, roaming, and a first look at wireless security.

CCNA 200-301 Domain 1.0 Network Fundamentals Verified 2026-10-11
Part 1

Radio waves as a medium

Wireless LANs transmit data on radio waves — electromagnetic radiation in the frequency ranges used for communication. A wireless NIC modulates a carrier wave to encode bits, an antenna radiates it, and the receiver’s antenna captures it. There is no cable to plug in, so hosts can move freely, but the medium is shared: every device in range competes for the same air, and anything else transmitting nearby — microwaves, Bluetooth, neighbours’ Wi-Fi, cordless phones — is interference.

Unlike copper or fibre, radio is a broadcast medium. A cable confines a signal to one path; a radio signal spreads in all directions and can be received by anyone in range. That is exactly why wireless security matters so much (Part 6).

Medium

Free space. Every device within range hears every transmission, so the band is shared.

Signal

A modulated carrier: information is carried in the power, frequency, or phase of the radio wave.

The trade

Freedom to move, at the cost of a shared medium, variable speed, and interference from anything else transmitting.

Part 2

The ISM bands: 2.4, 5, and 6 GHz

Wi-Fi operates in unlicensed frequency ranges set aside for industrial, scientific, and medical use — the ISM bands. Because they are unlicensed, anyone may transmit in them without a paid licence, which is why your home router, your neighbour’s, and your microwave all share the 2.4 GHz space.

BandRange & penetrationInterference / congestionTypical use
2.4 GHzBest range, best wall penetration (longer wavelength)Worst — crowded with Wi-Fi, Bluetooth, microwaves, cordless phonesCoverage over speed; legacy devices; IoT
5 GHzShorter range, poor wall penetrationMuch less interference; more channelsHigher throughput; most modern clients
6 GHzShortest range of the threeCleanest — new and nearly emptyWi-Fi 6E high-throughput, low-congestion

Lower frequencies travel farther and through walls better, but they have fewer usable channels and more competing devices. Higher frequencies carry more data and suffer less congestion but are blocked more easily by obstacles. The 6 GHz band is what enables Wi-Fi 6E; Wi-Fi 6 itself uses 2.4 and 5 GHz.

Exam tip. Remember the trade-off in one line: 2.4 GHz = range and penetration; 5/6 GHz = speed and less interference but shorter reach. If a question says “best coverage through walls”, choose 2.4 GHz; if it says “highest throughput, least congestion”, choose 5 or 6 GHz.
Pick the band · select a frequency

Part 3

Channels and overlap

Each band is divided into channels — narrow frequency slices a network can transmit on. Choosing different channels lets neighbouring networks reduce interference with each other. But in the 2.4 GHz band the channels are only 5 MHz apart while each channel is 20 MHz wide, so adjacent channels bleed into one another.

The classic result: in the widely used 1–11 channel set, only channels 1, 6, and 11 are non-overlapping. A network should pick one of these three and ensure neighbouring access points pick a different one. The 5 GHz band has far more channels and they are effectively non-overlapping, so it is much easier to avoid collisions there.

Why 1, 6, 11? Channels are numbered 5 MHz apart, so 1 → 6 → 11 are each five steps (25 MHz) apart — just far enough that these 20 MHz-wide channels do not overlap. Any other trio (for example 1, 5, 9) overlaps.
Channel overlap explorer · pick a set of channels
2.4 GHz band — 5 MHz channel spacing, 20 MHz wide channels Select a channel set above.

Part 4

SSID and the access point

The wireless access point (WAP) is the bridge between the wireless and wired worlds. A WAP has a radio to talk to clients and a wired (usually Ethernet) connection to the LAN; it forwards frames between the two, in the same way a switch forwards within the LAN. It broadcasts periodically so clients can find it.

The SSID (Service Set Identifier) is the human-readable network name that a WAP advertises — the name you pick from the list on your phone. Multiple access points that share the same SSID form one logical wireless network, letting clients roam between them. Each WAP also has a BSSID, which is the MAC address of its radio, used to identify the exact access point.

TermMeaning
SSIDThe wireless network name, up to 32 characters; shared by APs in the same network.
BSSIDThe MAC address of a specific access point’s radio.
WAPAccess point that connects wireless clients to the wired LAN.
Exam tip. SSID = the name (shared by every AP in the logical network, up to 32 characters). BSSID = the hardware address of one specific AP radio, so a network of three APs has one SSID and three BSSIDs.
Part 5

802.11 standards compared

The IEEE 802.11 family defines wireless LAN. Each amendment trades band and speed. The rates below are the theoretical maximums — real-world throughput is always lower because of overhead, interference, and distance.

StandardWi-Fi nameBand(s)Theoretical max rate
802.11a—5 GHzup to 54 Mbps
802.11b—2.4 GHzup to 11 Mbps
802.11g—2.4 GHzup to 54 Mbps
802.11nWi-Fi 42.4 + 5 GHzup to 600 Mbps
802.11acWi-Fi 55 GHzup to about 6.9 Gbps
802.11axWi-Fi 6 / 6E2.4 + 5 GHz (6 GHz for 6E)multi-Gbps, up to about 9.6 Gbps
Exam tip. Anchor the spine: a = 5 GHz/54 Mbps; b = 2.4 GHz/11 Mbps; g = 2.4 GHz/54 Mbps; n = both bands/600 Mbps; ac = 5 GHz/~6.9 Gbps; ax = both bands/up to ~9.6 Gbps. Note a and g share 54 Mbps but differ in band, and that only n and ax use both 2.4 and 5 GHz. All figures are theoretical maximums.
Standard decoder · select an 802.11 amendment

Part 6

Range, roaming and wireless security

Wireless always trades distance against speed. As a client moves farther from the access point, or through more walls, the signal weakens and the AP and client fall back to lower, more robust data rates. So the same link that gives 300 Mbps near the AP may give only a few Mbps at the far end of the house. Higher bands and wider channels raise the peak rate but reduce the usable range. Good wireless design places APs so that the required speed is available where users actually work.

One access point: 5 GHz reaches near and fast, 2.4 GHz reaches farther and slower WAP Laptop PC Phone 5 GHz — solid rings: near, fast 2.4 GHz — dashed: farther, slower

The WAP radiates on both bands. The solid 5 GHz coverage reaches nearby devices at high throughput; the dashed 2.4 GHz coverage reaches farther through the walls but at lower speed. Devices pick the band that offers the best balance of signal and rate.

Roaming and handoff

In a larger building, several access points share one SSID so the network appears as a single wireless network. As a client moves, it monitors signal strength and, when a neighbouring AP becomes a better choice, it reassociates to that AP without the user noticing. This process is called roaming or a handoff.

Roaming is a Layer 2 event: the client keeps its IP address because it stays on the same logical network. A fast, clean handoff is important for voice-over-Wi-Fi and other real-time traffic, since a slow one causes a brief drop in connectivity.

Wireless security in one page

Because radio is a broadcast medium, anyone in range can capture the traffic, so encryption and authentication are essential. The generations you must know:

ProtocolStatusNotes
WEPInsecure — do not useWired Equivalent Privacy; easily cracked in minutes; deprecated.
WPAInterimIntroduced TKIP as a stop-gap while WPA2 was developed; now also considered weak.
WPA2Current baselineUses AES with CCMP; strong and ubiquitous. Long passphrases matter.
WPA3Newest, strongestUses SAE to resist offline password-guessing; forward secrecy and better open-network protection.
Do not use WEP. WEP is broken and offers no real protection. The progression to remember is WEP (insecure) → WPA2 (the strong everyday standard) → WPA3 (the modern upgrade). Security is deepened in the security weeks (Week 8 and Week 10); this lesson only fixes the order.
Wireless security generations · select a protocol

Part 7 · Your turn

Review

Check what you have learned with these review questions.

Review · 6 questions

Sources

Sources & references

  1. IEEE. IEEE 802.11 Wireless LAN standards (802.11a/b/g/n/ac/ax). standards.ieee.org.
  2. Wi-Fi Alliance. Wi-Fi 4/5/6/6E generation naming and WPA2/WPA3 certification. wi-fi.org.
  3. Cisco. CCNA (200-301) Exam Topics — Network Fundamentals (wireless principles). cisco.com.
  4. Cisco. CCNA: Introduction to Networks — “Network Media” (wireless media, channels, SSID, and standards). netacad.com.

Target exams: CCNA 200-301 v1.1 · CyberOps Associate 200-201. Last content verification: 2026-10-11.