Week 5 · Lesson 4

Main Devices in the Data Link Layer

The machines that live at Layer 2 — the NIC, the switch, the historical bridge, and the wireless access point — are what turn MAC addressing into a working network. Understanding them also means mastering two ideas the exam tests hard: collision domains and broadcast domains.

CCNA 200-301 Domain 1.0 Network Fundamentals Verified 2026-10-11
Part 1

Network interface card (NIC)

The NIC (also called a network adapter or LAN adapter) is the hardware that connects a host to the network medium. It is the boundary between data and signals: it takes a Layer-3 packet handed down by the operating system, builds the Layer-2 frame, adds the MAC address, and converts the frame into the electrical, optical, or radio signals the medium carries. On receive, it does the reverse — reads signals, checks the FCS, and passes the packet up.

Every interface that connects to the network has its own NIC and its own MAC address. A device with both an Ethernet port and a Wi-Fi radio has two interfaces and therefore two MAC addresses.

Part 2

Switch

A switch is a multiport Layer-2 device. Its job is to forward frames between the devices connected to it, using the destination MAC address. It does this with a MAC address table (also called the CAM table) that maps MAC addresses to switch ports.

How a switch builds and uses the table:

Exam tip. A switch learns from the source MAC and forwards based on the destination MAC. Getting those two backwards is the most common mistake. Also remember a switch forwards within one Layer-2 network (it does not cross subnets).
Part 3

Bridge (historical)

A bridge is the ancestor of the switch. It was a software-based device that joined two LAN segments, learning MAC addresses and forwarding frames between them — so it worked at Layer 2 exactly like a switch. In fact, a bridge is functionally a two-port switch.

AspectBridgeSwitch
PortsTypically twoMany (often 24–48+)
ImplementationSoftware (CPU-based)Hardware (ASIC), very fast
Forwarding logicMAC address tableMAC address table (same idea)
TodayObsolete as a separate deviceEverywhere in modern LANs

Because switches are just fast, high-port-count bridges, the terms “bridge” and “switch” describe the same Layer-2 function. You will still see “bridging” used for certain software functions and for wireless bridging.

Part 4

Wireless access point and WLC

A wireless access point (AP) lets wireless hosts join the wired network. It bridges the Wi-Fi medium (radio) to the Ethernet medium (cable), forwarding frames between them — a Layer-2 role. Wireless hosts are half-duplex and share the air, so the AP coordinates access using CSMA/CA.

In business networks, many APs are managed centrally by a Wireless LAN Controller (WLC). The controller centralises configuration, security policy, and roaming for all APs. In a controller-based design, lightweight APs typically build a tunnel (CAPWAP) back to the WLC. The WLC is the management brain; the APs still do the radio work at Layer 1 and frame handling at Layer 2.

Note. An AP is a Layer-2 bridge between wireless and wired. A router in a home “wireless router” is a separate function (Layer 3) bundled into the same box. Do not treat the AP as a router.
The Layer-2 device family · select one

Part 5

Collision domains vs broadcast domains

These two terms describe how far two kinds of traffic can spread. They are central to the exam.

Collision domain. The set of devices whose frames can collide with each other (they share one medium).
Broadcast domain. The set of devices that receive a broadcast frame sent by any one of them.
DeviceCollision domainsBroadcast domains
Hub / repeaterOne shared domain for all portsDoes not divide — one
NICBelongs to one collision domain (its link)Does not divide
Switch portEach port is its own collision domainDoes not divide — all ports share one L2 broadcast domain (per VLAN)
RouterEach interface is its own domainDivides — each interface is a separate broadcast domain

A switch segments collision domains. Because each connection runs on its own port, devices on different ports cannot collide with each other. A hub, by contrast, repeats every signal to every port, so all its devices are in one collision domain and contend for the same bandwidth.

A switch does not segment broadcast domains. A broadcast sent to FF:FF:FF:FF:FF:FF is flooded out every port in the VLAN. To break a broadcast domain you need a router or VLANs, which create logically separate Layer-2 networks.

Hub or switch · 4 hosts, one segment
Exam tip. Classic trick question: “How many broadcast domains does a 24-port switch create?” Answer: one (unless it is configured with multiple VLANs). How many collision domains? 24 — one per port.
Part 6

Half duplex vs full duplex

Duplex describes whether a link can send and receive at the same time.

ModeData flowCollisionsTypical use
Half duplexSend or receive, but not both at oncePossible; handled by CSMA/CDShared hub links; legacy shared media
Full duplexSend and receive simultaneouslyNone; CSMA/CD is disabledPoint-to-point switch-to-host and switch-to-switch links

Full duplex is possible only on a point-to-point link with separate transmit and receive paths — which is exactly what a switch provides on each port. Because there can be no collisions, the full bandwidth is available in each direction, and the link no longer counts as a shared collision domain. Modern Ethernet links between a host and a switch normally run at full duplex; a mismatch (one side half duplex, the other full) is a classic cause of errors and poor performance.

Duplex mismatch · set each end
S1 S2
  • Full-duplex: both ends of the connection can send and receive at the same time. Half-duplex: only one end can send at a time.
  • Autonegotiation is an optional function on most Ethernet switches and NICs. It lets two devices negotiate the best speed and duplex automatically. Both sides of a link should have it on, or both should have it off.
  • A mismatch can happen when one or both ports are reset and autonegotiation does not give both ends the same setting, or when someone reconfigures one side of a link and forgets the other.
  • Gigabit Ethernet ports only operate in full-duplex.
Part 7 · Your turn

Review

Check what you have learned with these review questions.

Review · 6 questions

Sources

Sources & references

  1. IEEE. IEEE 802.3: Ethernet (switching, duplex operation, CSMA/CD). standards.ieee.org.
  2. IEEE. IEEE 802.11: Wireless LAN (access points, CSMA/CA). standards.ieee.org.
  3. Braden, R. RFC 1122: Requirements for Internet Hosts — Communication Layers (1989), Section 1.3.3. rfc-editor.org/rfc/rfc1122.
  4. Cisco. CCNA (200-301) Exam Topics, Network Fundamentals. cisco.com.

Target exams: CCNA 200-301 v1.1 · CyberOps Associate 200-201. Last content verification: 2026-10-11.