Ethernet Frames
This is the canonical lesson on the Ethernet frame. Learn every field and its exact size in octets, the minimum and maximum frame lengths, and the values that appear in the EtherType field. These numbers are tested directly, so treat them as memorisation targets, not background reading.
- Name every field of the Ethernet II frame with its size in octets.
- State the minimum (64) and maximum (1518 / 1522) frame sizes.
- Explain the role of the Preamble and SFD, and why they are not counted.
- Distinguish Ethernet II (Type) from IEEE 802.3 (Length) + LLC/SNAP.
- Recall the canonical EtherType values for IPv4, IPv6, and ARP.
- Define runt and giant frames.
The standard: IEEE 802.3
Ethernet is standardised as IEEE 802.3. Two frame formats live under that umbrella, and exam questions use both:
- Ethernet II (also called DIX Ethernet, after DEC–Intel–Xerox) — the dominant format used on virtually all modern networks. Its field after the source address is a Type value.
- IEEE 802.3 with LLC/SNAP — a variant whose field after the source address is a Length value, followed by an IEEE 802.2 LLC header (and often a SNAP header) inside the payload.
Everything that follows describes the Ethernet II frame, which is what you will meet in practice and on the exam.
The Ethernet II fields
Here are the fields in order, with their sizes in octets (bytes). Memorise this table cold.
| Field | Size (octets) | Purpose |
|---|---|---|
| Preamble | 7 | Bit-synchronisation pattern (alternating 1/0) so the receiver can lock onto the signal. |
| Start Frame Delimiter (SFD) | 1 | Ends the sync pattern and marks the start of the frame (value 10101011). |
| Destination MAC address | 6 | Layer 2 address of the receiving device (or a broadcast/multicast address). |
| Source MAC address | 6 | Layer 2 address of the sending device. |
| Type / Length | 2 | EtherType identifies the upper-layer protocol (Ethernet II); or the payload length (IEEE 802.3). |
| Payload (Data) | 46–1500 | The encapsulated data — the PDU from the Network layer (for example, an IPv4 packet). |
| Frame Check Sequence (FCS) | 4 | CRC-based error-detection value computed over the frame. |
Preamble and Start Frame Delimiter
The first 8 octets are not really part of the message; they are there so the two ends of the link agree on where the frame begins at the bit level. The Preamble is 7 octets of the pattern 10101010, giving the receiver time to synchronise its clock. The Start Frame Delimiter (SFD) is 1 octet, 10101011; the final two bits differ from the preamble pattern and announce “the frame starts now”.
Destination and Source addresses
Both the Destination and Source addresses are 6 octets (48 bits) — the MAC addresses you will study in lesson 09. The Destination comes first, because a receiving station wants to check whether the frame is for it as early as possible. A destination of FF:FF:FF:FF:FF:FF is the broadcast address and is received by every station on the local segment.
Type vs Length: Ethernet II and 802.3
The 2-octet field after the source address is the crux of the Ethernet II vs IEEE 802.3 difference. It is interpreted by its numeric value:
- If the value is ≥ 0x0600 (1536), it is an EtherType that names the upper-layer protocol — this is Ethernet II.
- If the value is ≤ 1500, it is a Length giving the size of the payload — this is IEEE 802.3. The first bytes of the payload then carry an LLC (Logical Link Control, IEEE 802.2) header, whose DSAP/SSAP/control fields identify the protocol; a SNAP extension adds an OUI and an EtherType for protocols LLC cannot name.
| Aspect | Ethernet II (DIX) | IEEE 802.3 (LLC/SNAP) |
|---|---|---|
| Field after Source | Type (EtherType) | Length |
| Protocol identification | Directly by EtherType | By LLC (and SNAP) inside the payload |
| Typical use today | All common LAN traffic | Legacy; some control protocols |
The canonical EtherType values you must know:
| EtherType | Protocol |
|---|---|
0x0800 | IPv4 |
0x86DD | IPv6 |
0x0806 | ARP (Address Resolution Protocol) |
0x8100 | IEEE 802.1Q VLAN tag (indicates a tagged frame) |
0x0800.
If it carries an IPv6 packet, 0x86DD.
Payload and FCS
The Payload (Data) field carries the encapsulated protocol data unit, from 46 to 1500 octets. If the actual data is shorter than 46 octets, the sender pads it with zeros so the frame still reaches the 64-octet minimum. The Frame Check Sequence (FCS) is the final 4 octets: a CRC computed by the sender and verified by the receiver. A frame whose FCS does not match is discarded silently — Ethernet does not retransmit at Layer 2 (see Lesson 5).
Minimum, maximum, VLAN, and jumbo
Know these numbers and the reasoning behind them:
- Minimum frame = 64 octets, counted from the Destination address through the FCS. Senders pad short payloads to reach it. The reason is collision detection on a shared half-duplex segment (Lesson 7): a station must still be transmitting when a collision returns.
- Maximum frame = 1518 octets (DA through FCS): 6 + 6 + 2 + 1500 + 4.
- With an 802.1Q VLAN tag = 1522 octets: the 4-octet tag is inserted after the
source address, so the maximum grows by 4. The tag begins with the value
0x8100in the Type field. - Jumbo frames (~9000 octets) — optional and vendor-specific, extending the MTU to about 9000. Not part of the base standard; supported only when every device on the path agrees.
The frame, field by field
The diagram shows the octet sizes of each field. Note how the 8 synchronisation octets sit outside the measured frame.
Octets: 7 1 6 6 2 46..1500 4
+--------+--------+----------+----------+-----------+-------------+-------+
Field: |Preamble| SFD | Dest | Source | Type / | Payload | FCS |
| | | MAC | MAC | Length | (Data) | |
+--------+--------+----------+----------+-----------+-------------+-------+
\_______ 8 octet sync ______/
(NOT part of the 64-byte minimum)
|<----------- MIN 64 octets .. MAX 1518 octets (DA -> FCS) ----------->|
EtherType values: 0x0800 = IPv4 0x86DD = IPv6 0x0806 = ARP 0x8100 = 802.1Q tag
Read it left to right: the receiver synchronises on the preamble and SFD, checks the destination MAC, learns the source MAC, reads the Type to know what is inside, consumes the payload, and finally verifies the FCS. The 802.1Q VLAN tag, when present, is a 4-octet addition between Source and Type/Length.
Worked 64-byte breakdown
Why is the minimum frame exactly 64 octets? Add the smallest legal field sizes from the Destination address through the FCS:
Destination MAC ....... 6
Source MAC ............ 6
Type / Length ......... 2
Minimum payload ....... 46
FCS ................... 4
----
Minimum frame ......... 64 octets
Inversely, the minimum payload is whatever is needed to reach 64:
64 - (6 + 6 + 2 + 4) = 64 - 18 = 46 octets
Maximum frame:
6 + 6 + 2 + 1500 + 4 = 1518 octets
With an 802.1Q VLAN tag (4 extra octets):
1518 + 4 = 1522 octets
On the wire, add the 8 sync octets:
64 + 8 = 72 octets transmitted for a minimum-size frame
The MTU is the payload ceiling, 1500 octets (see Lesson 7); the whole frame adds 18 octets of header and trailer to that payload, giving the 1518 maximum.
Runts and giants
| Frame | Size | Meaning and action |
|---|---|---|
| Runt | Shorter than 64 octets (DA–FCS) | Usually a collision fragment or a truncation error. The receiving NIC discards it. |
| Normal | 64–1518 octets (1522 with VLAN) | A valid Ethernet frame. |
| Giant | Longer than the maximum for the link | Frames above 1518 (or above an agreed jumbo MTU) are invalid and dropped. |
The vocabulary you need
Every term below appears in the lesson text above. Select one to read its definition, then use the quiz at the end to check what stuck.
Review
Check what you have learned with these review questions.
Sources & references
- Cisco. CCNA (200-301) Exam Topics. cisco.com.
- IETF. Request for Comments (RFCs). rfc-editor.org.
- IANA. Internet Assigned Numbers Authority registries. iana.org.
Target exams: CCNA 200-301 v1.1 · CyberOps Associate 200-201. Last content verification: 2026-10-11.