Week 5 · Lesson 12

Switched Networks and VLANs

A plain switch keeps every port in one giant broadcast domain — efficient for four desks, unworkable for four hundred. A VLAN splits that one domain into many virtual LANs at Layer 2, and almost every switch question on the CCNA turns on this one idea: the switch segments collisions, but only a VLAN (or a router) segments broadcasts.

CCNA 200-301 Domain 2.0 Network Access Verified 2026-10-11
Learning objectives
Part 1

The flat broadcast domain

You saw in Lesson 11 that a switch increases the number of collision domains (it gives every port its own) but leaves the broadcast domain untouched. Legally, all ports of an unconfigured switch belong to the same Layer 2 group: every broadcast frame that arrives on any port is flooded out of every other port, and every host hears it. In a small office with half a dozen machines this is harmless. Add hundreds of hosts, and it is a problem.

Each broadcast frame interrupts every CPU on the segment for the instant it takes the NIC to discover the frame is not for it. Layer 2 discovery protocols, ARP requests, DHCP DISCOVERs, and service announcements all generate broadcasts constantly. The result is a slow, noisy, insecure segment where any host can sniff every neighbour’s conversations and one misconfigured machine can disturb the whole floor. This single undivided segment is what a VLAN is designed to cut into pieces.

Definition — VLAN A VLAN (Virtual Local Area Network) is a logical subdivision of a switched network at Layer 2. Devices in the same VLAN behave as if they were on the same physical LAN — they share one broadcast domain — even when their ports are scattered across different switches. Devices in different VLANs cannot communicate directly at Layer 2 at all.
In this lesson · select a part to jump

Key ideas & exam traps · select one

Part 2

What a VLAN is

When you create VLAN 10 on a switch, you are telling the switch: ports in VLAN 10 form one broadcast domain, and ports not in VLAN 10 are invisible to them. The switch enforces this in its forwarding logic. A frame learned from a VLAN 10 port may be forwarded only to other VLAN 10 ports. VLAN 20 frames are handled by the same hardware but treated as a separate universe — a separate broadcast domain, a separate MAC address table region, a separate Layer 2 network.

This is the phrase to remember: a VLAN is a broadcast domain. One VLAN — one broadcast domain. If a question says two PCs are in the same VLAN, they can reach each other at Layer 2; if they are in different VLANs, they cannot — something at Layer 3 must join them (Lesson 15).

No VLANs — one broadcast domain Two VLANs — two broadcast domains broadcast reaches every host Switch all ports, VLAN 1 PC A PC B PC C PC D VLAN 10 — broadcasts stop here VLAN 20 — never sees VLAN 10 traffic Switch VLAN 10 + VLAN 20 PC E PC F PC H PC G
Both halves show the same three ingredients — hosts, a switch, a broadcast — but the right half has been split by VLANs. VLAN 10 and VLAN 20 are separate broadcast domains on one physical switch.
Part 3

Why VLANs exist: security, performance, flexibility

The exam will ask you to justify a VLAN design. The three accepted reasons are security, performance, and flexibility (or organisational grouping). Learn the one-line argument for each.

Exam tip VLANs are often described as providing security and performance by reducing broadcast domains, plus simplified administration because groups no longer need physical co-location. If a question offers “VLANs increase the number of broadcast domains” that is correct and usually the intended answer — they shrink each one, which is the point.
Part 4

VLAN ranges and reserved numbers

Cisco switches divide the VLAN ID space in two, and the boundary is a favourite fact:

RangeIDsHow they can be used
Normal range1–1005Configurable on any platform; stored in the VLAN database (vlan.dat for IOS); advertised by VTP.
Extended range1006–4094Available on most modern switches but not stored in vlan.dat; must be configured globally, not per-port, and VTP will not carry them (switch must be in VTP transparent mode).
Reserved legacy1002–1005Token Ring and FDDI VLANs; present by default and cannot be deleted.
Reserved system0 and 4095Never usable for user traffic; reserved for 802.1Q system use.

Note the trap: 1002–1005 sit inside the normal range but are reserved for the legacy Token Ring and FDDI translations, so in practice the VLANs you will ever create sit in 2–1001 (normal) or 1006–4094 (extended). The extended range tops out at 4094, not 4096 — the 12-bit VLAN ID field gives 4096 values, but 0 and 4095 are reserved, leaving 4094 usable IDs.

Watch out Two facts collide here on real exams. First, the VLAN ID field in the 802.1Q tag is 12 bits, so IDs go from 0 to 4095. Second, the usable range on Cisco switches is 1–4094. A question that mixes “4096 VLANs possible” with “4094 configurable” is testing exactly this distinction.
Reference table · select a row

Part 5

Default and native VLAN 1

Out of the box, every port on a Cisco switch is an access port in VLAN 1, and VLAN 1 is the default VLAN. It cannot be renamed or deleted. VLAN 1 is also the native VLAN by default — the VLAN whose frames travel across a trunk without a tag (Lesson 14).

Because VLAN 1 is where everything lands until you say otherwise, it is a security concern: any untagged traffic that arrives on a trunk enters VLAN 1. Best practice in production is to move management traffic out of VLAN 1 and to make the native VLAN something other than VLAN 1. The exam tests the facts: VLAN 1 is default, is native by default, and cannot be deleted.

Definition — data VLAN vs voice VLAN A data VLAN carries ordinary user traffic (PCs, servers, printers). A voice VLAN is a separate VLAN dedicated to IP telephony, configured on the same access port so that one cable can carry both the phone’s audio and the PC’s data.
Part 6

Data VLAN vs voice VLAN

IP phones sit between the switch and the PC and carry two kinds of traffic: the phone’s itself (signalling and RTP audio) and the PC’s data that passes through the phone’s built-in switch. Mixing both on one VLAN would let voice traffic compete with noisy PC traffic, so Cisco design separates them:

Conceptual exam questions ask: “Where should IP phones go?” Answer: a dedicated voice VLAN, so that phones are grouped, QoS can be applied cleanly, and a PC’s broadcast storm cannot choke call control traffic. Configuration — the switchport voice vlan command — is Lesson 13.

Part 7

The cost: inter-VLAN traffic needs a router

Segmentation is not free. Two devices in VLAN 10 and VLAN 20 are Layer 2 strangers: their frames never cross the VLAN boundary, and broadcasts do not either. For them to exchange data, the traffic must be routed — which means it must be sent to a Layer 3 device (a router, or a Layer 3 switch) that holds an interface in each VLAN. This is inter-VLAN routing, and it is the whole of Lesson 15. For now, hold the one-line cost: VLANs demand a router for cross-VLAN communication.

Put the two lessons together. A switch partitions broadcast domains by VLAN; a VLAN is a broadcast domain; therefore moving a host into a new VLAN both protects and isolates it. Every design answer that involves VLANs is really an answer about where the Layer 3 boundary will be.

Note A VLAN does not change the physical cabling or the number of switches; it is purely a switch-side configuration. That is why it is called virtual — the LAN is logical, not physical.
Key terms

The vocabulary you need

Every term below appears in the lesson text above. Select one to read its definition, then use the quiz at the end to check what stuck.

Key terms · select a term

Part 8 · Your turn

Review

Check what you have learned with these review questions.

Review · 5 questions

Sources

Sources & references

  1. Cisco. CCNA (200-301) Exam Topics. cisco.com.
  2. IETF. Request for Comments (RFCs). rfc-editor.org.
  3. IANA. Internet Assigned Numbers Authority registries. iana.org.

Target exams: CCNA 200-301 v1.1 · CyberOps Associate 200-201. Last content verification: 2026-10-11.