Exam Center · Practice Exam

Practice Exam 1

A full-length, four-part practice exam of 56 questions spanning all six CCNA domains. Set a timer for 120 minutes, sit it in one sitting with no notes, then score yourself here. The mix of questions, not the format, is what prepares you: every answer explains the reasoning so a wrong guess becomes a lesson.

CCNA 200-301 v1.1 56 questions 120 minutes Verified 2026-10-11

How to sit this exam

The real CCNA is a 120-minute exam of about 100 questions, and the pass mark has historically been around 825 out of 1000 (roughly 82%). Cisco does not publish a hard cut-off, so use a practical target: aim for 85% or better here, and treat anything below 80% as a signal to revisit the domain before exam day.

Give yourself the full 120 minutes for these 56 questions — that is generous, which is deliberate. Use the spare time to re-read flagged questions. Mark every question you guessed, even when you answer correctly: a guess that lands is still a gap in knowledge.

Exam tip — the four parts The exam is split into Part 1 Fundamentals, Part 2 Network Access, Part 3 IP Connectivity, and Part 4 IP Services, Security, and Automation. Work in order, then review. The score bars show your progress per part, and the summary above tracks the whole attempt.

Part 1 — Network Fundamentals

Select the single best answer. Feedback and an explanation appear immediately after you choose.

Practice Exam 1 · Part 1 — Fundamentals
  1. Which OSI layer is responsible for logical addressing and path selection between networks?

    • Physical
    • Data Link
    • Network
    • Transport

    Layer 3 (Network) carries the logical address — an IP address — and routers use it to choose a path. Physical deals with bits, Data Link with frames and MAC addresses, Transport with end-to-end segments.

  2. Which device forwards frames based on MAC addresses within a single broadcast domain?

    • Router
    • Switch
    • Firewall
    • Modem

    A switch learns MAC addresses and forwards frames inside one LAN. A router forwards packets between networks using IP addresses; a firewall filters traffic.

  3. A company must connect two different IP subnets so hosts can communicate. Which device is required?

    • Switch
    • Hub
    • Router
    • Repeater

    Different subnets means Layer 3 forwarding, which is a router's job. Switches, hubs, and repeaters all stay within one subnet.

  4. In the TCP/IP model, which layer corresponds to OSI Layers 5, 6, and 7?

    • Network Access
    • Internet
    • Transport
    • Application

    The TCP/IP Application layer folds together the OSI Session, Presentation, and Application layers. Its Network Access layer merges OSI Data Link and Physical.

  5. How many usable host addresses does a /27 subnet provide?

    • 30
    • 32
    • 62
    • 126

    A /27 leaves 5 host bits: 25 = 32 addresses, minus the network and broadcast = 30 usable hosts.

  6. Which of these is a valid RFC 1918 private IPv4 address?

    • 172.32.0.1
    • 11.0.0.1
    • 192.168.10.5
    • 169.254.1.1

    The private ranges are 10.0.0.0/8, 172.16.0.0/12 (172.16–172.31), and 192.168.0.0/16. 169.254.0.0/16 is APIPA, not RFC 1918.

  7. Which IPv6 address type begins with the prefix FE80::/10?

    • Global unicast
    • Link-local
    • Unique local
    • Multicast

    Link-local addresses are FE80::/10 and are used on a single link. Global unicast is 2000::/3, unique local is FC00::/7, and multicast is FF00::/8.

  8. Which is the correct compressed form of 2001:0db8:0000:0000:0000:ff00:0042:8329?

    • 2001:db8::ff00:42:8329
    • 2001:0db8::ff00:42:8329
    • 2001:db8:0:0:0:ff00:42:8329::
    • 2001:db8::ff00::42:8329

    Leading zeros are dropped (0db8 → db8, 0042 → 42) and the single longest run of zero groups becomes ::, which may appear only once.

  9. Which cabling type carries a single light path and supports the longest distances?

    • Cat 6 UTP
    • Multimode fiber
    • Single-mode fiber
    • Coaxial

    Single-mode fiber has a small core and one light path, so it reaches the farthest of any medium taught here. Multimode fiber uses multiple paths and shorter distances; copper is shorter still.

  10. One side of a link auto-negotiates 1000 Mbps and the other negotiates 100 Mbps. What is the likely outcome?

    • Full-speed 1000 Mbps operation
    • A speed mismatch that degrades or breaks the link
    • A duplex mismatch only
    • No change at all

    When speed differs, the link either fails to come up or runs poorly. A duplex mismatch is a separate fault, where both ends agree on speed but not on duplex.

  11. What type of address is FF:FF:FF:FF:FF:FF?

    • Unicast
    • Multicast
    • Broadcast
    • Anycast

    The all-ones MAC address is the Layer 2 broadcast address, received by every device in the broadcast domain.

  12. Which transport protocol is connection-oriented and uses a three-way handshake?

    • UDP
    • ICMP
    • TCP
    • ARP

    TCP opens a connection with SYN, SYN-ACK, ACK and provides reliability. UDP is connectionless; ICMP and ARP are not transport protocols.

  13. Which command displays the IP configuration on a Windows host?

    • ifconfig
    • ipconfig
    • ip addr
    • netstat

    Windows uses ipconfig. Linux and older macOS use ifconfig or ip addr; macOS also uses ifconfig. netstat shows connections, not addressing.

  14. Which concept describes delivering both electrical power and data over the same Ethernet cable?

    • Power over Ethernet (PoE)
    • A VLAN
    • Spanning Tree
    • NAT

    PoE lets a switch power devices such as access points and IP phones, removing the need for a separate power outlet at the device.

  15. Which is a valid reason to use private IPv4 addressing?

    • To route the addresses directly on the public Internet
    • To conserve public addresses and enable NAT
    • To avoid subnetting entirely
    • To increase link bandwidth

    Private addresses can be reused inside every organisation, and NAT translates them to public addresses at the edge. They are not routable on the public Internet.

  16. Which statement best describes server virtualization?

    • Running multiple logical systems on shared physical hardware
    • Physically duplicating every server
    • A routing protocol for data centres
    • A wireless encryption standard

    Virtualization runs several virtual machines or containers on one physical host, sharing CPU, memory, and network adapters. It is not a protocol or a wireless standard.

Part 2 — Network Access

VLANs, trunking, discovery, EtherChannel, STP, and wireless.

Practice Exam 1 · Part 2 — Network Access
  1. What is the default native VLAN on an 802.1Q trunk?

    • VLAN 100
    • VLAN 1
    • VLAN 0
    • There is no default

    VLAN 1 is the default native VLAN, and its traffic crosses a trunk untagged. Best practice is to move it to an unused VLAN, but the default remains VLAN 1.

  2. Which command places an interface into VLAN 20 as an access port?

    • switchport mode trunk
    • switchport access vlan 20
    • vlan 20 access
    • switchport trunk vlan 20

    switchport access vlan 20 assigns the port's access VLAN. The other options set trunking, are invalid syntax, or apply to trunk VLANs.

  3. Which discovery protocol is an open standard and vendor-neutral?

    • CDP
    • LLDP
    • DTP
    • VTP

    LLDP is IEEE 802.1AB and works between vendors. CDP is Cisco-proprietary; DTP negotiates trunking and VTP propagates VLAN databases.

  4. Which STP feature immediately places an access port into the forwarding state?

    • PortFast
    • UplinkFast
    • BackboneFast
    • Root guard

    PortFast skips the listening and learning delays on a port connected to an end device. UplinkFast and BackboneFast are legacy convergence tools; root guard protects the root role.

  5. What is the default bridge priority used by Spanning Tree?

    • 4096
    • 8192
    • 32768
    • 65536

    The default bridge priority is 32768, and it changes in steps of 4096. The switch with the lowest bridge ID becomes root.

  6. Which switch is elected as the STP root bridge?

    • The one with the lowest bridge ID
    • The one with the highest bridge ID
    • The one with the lowest MAC address only
    • The one with the highest port number

    The lowest bridge ID wins. The bridge ID combines priority and MAC, so a low priority beats a lower MAC unless the priorities are equal.

  7. Which pair of keywords is used for LACP EtherChannel negotiation?

    • on / off
    • active / passive
    • desirable / auto
    • trunk / access

    LACP uses active and passive. Desirable/auto belongs to PAgP, and on/off bypasses negotiation entirely.

  8. Which command configures an EtherChannel to a router using LACP?

    • channel-group 1 mode active
    • channel-group 1 mode desirable
    • channel-group 1 mode on
    • channel-group 1 mode auto

    A router supports LACP, which uses mode active. Desirable and auto are PAgP, and on forces the bundle without negotiation.

  9. What is the purpose of the native VLAN on an 802.1Q trunk?

    • To tag every frame crossing the trunk
    • To carry untagged traffic across the trunk
    • To block STP BPDUs
    • To route between VLANs

    The native VLAN carries frames that are not tagged with an 802.1Q header. If the two ends disagree, a native VLAN mismatch results, and traffic can leak between VLANs.

  10. Which feature prevents a rogue switch from becoming the STP root?

    • BPDU guard
    • Root guard
    • Port security
    • Dynamic ARP inspection

    Root guard stops a superior BPDU on a designated port, keeping the current root. BPDU guard shuts a PortFast port that receives any BPDU.

  11. Which discovery protocol is Cisco-proprietary?

    • LLDP
    • CDP
    • STP
    • VTP

    CDP (Cisco Discovery Protocol) is proprietary. LLDP is the open standard, and STP and VTP are not discovery protocols.

  12. In a controller-based wireless network, which AP mode tunnels client traffic back to the WLC by default?

    • FlexConnect
    • Local
    • Sniffer
    • Bridge

    In local mode the AP builds a CAPWAP tunnel to the WLC and client traffic is centralised there. FlexConnect can switch traffic locally; sniffer and bridge are specialised modes.

  13. When an IP phone is attached to a switch port, which VLAN arrangement is typical?

    • One VLAN only
    • A data VLAN plus a voice VLAN on the same port
    • A trunk with no access VLAN
    • The native VLAN only

    The port carries both a data VLAN for the attached PC and a voice VLAN for the phone, tagged with 802.1Q so the phone can separate the two.

  14. Which remote management method encrypts the session?

    • Telnet
    • HTTP
    • SSH
    • FTP

    SSH encrypts the management session. Telnet and HTTP send credentials in clear text, and FTP transfers files without encryption.

Part 3 — IP Connectivity

Routing tables, forwarding decisions, static routing, OSPFv2, and first hop redundancy.

Practice Exam 1 · Part 3 — IP Connectivity
  1. What is the administrative distance of OSPF?

    • 90
    • 100
    • 110
    • 120

    OSPF is 110. EIGRP is 90, RIP is 120, static is 1, and connected is 0. Lower administrative distance is preferred.

  2. A router learns the same prefix from a static route and from OSPF. Which route enters the routing table?

    • The OSPF route
    • The static route
    • Both, by load-balancing
    • Neither

    Administrative distance decides first: static is 1 and OSPF is 110, so the static route wins. Equal-cost load-balancing only happens within the same protocol and metric.

  3. A router has both 10.1.0.0/16 and 10.1.1.0/24 in its table and must forward a packet to 10.1.1.5. Which route does it use?

    • The /16 route
    • The /24 route
    • Both, in parallel
    • Neither

    Longest prefix match wins: the /24 is more specific than the /16, so it is preferred for 10.1.1.5 regardless of administrative distance.

  4. Which command creates a default route out through 192.168.1.1?

    • ip route 0.0.0.0 0.0.0.0 192.168.1.1
    • ip default-gateway 192.168.1.1
    • ip route 192.168.1.1 255.255.255.255
    • route add default 192.168.1.1

    ip route 0.0.0.0 0.0.0.0 192.168.1.1 is the default route. ip default-gateway is for a host-mode device without routing enabled, and the others are invalid or single-host routes.

  5. A floating static route is configured with which characteristic?

    • A higher administrative distance
    • A lower metric
    • A different routing protocol
    • No next hop

    A floating static is a backup: a deliberately high administrative distance keeps it out of the table until the primary route fails.

  6. Which OSPF packet discovers and maintains neighbour relationships?

    • LSA
    • Hello
    • Database Description (DBD)
    • Link State Update (LSU)

    Hello packets form and maintain adjacencies, carrying the router ID and parameters. DBD and LSU exchange and flood database information.

  7. On a broadcast OSPF network, which multicast address do all OSPF routers listen on?

    • 224.0.0.5
    • 224.0.0.6
    • 224.0.0.9
    • 224.0.0.10

    224.0.0.5 is AllSPFRouters. 224.0.0.6 is AllDRouters, used by the DR and BDR. 224.0.0.9 and 224.0.0.10 belong to RIPv2 and EIGRP.

  8. On a broadcast OSPF network, which devices receive updates sent to 224.0.0.6?

    • All routers
    • Only the DR and BDR
    • Only the DR
    • Only the ABR

    224.0.0.6 is AllDRouters: only the designated and backup designated routers listen. All other routers use 224.0.0.5.

  9. If no router ID is configured, how does OSPF choose one?

    • Highest loopback address, else highest physical interface IP
    • Lowest loopback address, else lowest physical IP
    • The interface MAC address
    • The device hostname

    OSPF prefers the highest loopback address; without a loopback it uses the highest IP of an active physical interface. An explicit router-id always overrides both.

  10. Which protocol is a first hop redundancy protocol?

    • OSPF
    • HSRP
    • LACP
    • DTP

    HSRP is a Cisco first hop redundancy protocol that gives hosts a stable virtual gateway. OSPF is a routing protocol; LACP bundles links; DTP negotiates trunking.

  11. What is the default HSRP priority?

    • 1
    • 100
    • 110
    • 255

    HSRP defaults to priority 100, with a higher value winning. VRRP also defaults to 100.

  12. In HSRP, which router becomes the active gateway?

    • Highest priority, then highest IP address
    • Lowest priority
    • Highest MAC address
    • Chosen at random

    The highest priority wins; ties are broken by the highest interface IP address. Preemption is off by default unless configured.

  13. Which MAC address does HSRP use for its virtual gateway?

    • 0000.0C07.ACxx
    • 0000.5E00.01xx
    • FFFF.FFFF.FFFF
    • 0180.C200.0000

    HSRP v1 uses 0000.0C07.ACxx, where xx is the group number. 0000.5E00.01xx is VRRP's virtual MAC.

  14. Which metric does OSPF use by default?

    • Hop count
    • Cost
    • Bandwidth in kbps
    • Delay

    OSPF cost is derived from interface bandwidth: 108 divided by bandwidth in bits per second at the default reference. Hop count is RIP's metric.

Part 4 — IP Services, Security & Automation

NAT, DHCP, NTP, syslog, SNMP, QoS, ACLs, Layer 2 security, wireless security, and automation.

Practice Exam 1 · Part 4 — Services, Security, Automation
  1. Which NAT type lets many inside hosts share one public address using unique source ports?

    • Static NAT
    • Dynamic NAT
    • PAT (overload)
    • NAT64

    PAT, also called NAT overload, tracks inside hosts by source port so one public address serves many sessions. Dynamic NAT uses a pool of public addresses.

  2. Which command enables PAT using an ACL on an interface?

    • ip nat inside source list 1 interface g0/0 overload
    • ip nat inside source static
    • ip nat pool
    • ip nat destination

    The overload keyword turns the translation into PAT. static is one-to-one, and a pool creates dynamic NAT without port overloading.

  3. Which transport protocol and port does NTP use?

    • TCP 123
    • UDP 123
    • UDP 69
    • TCP 49

    NTP uses UDP 123. UDP 69 is TFTP and TCP 49 is TACACS+.

  4. In DORA, which DHCP message does a client send first?

    • Offer
    • Request
    • Discover
    • Acknowledge

    DORA is Discover, Offer, Request, Acknowledge. The client begins with a broadcast Discover; the server replies with an Offer.

  5. Which syslog severity level represents the most severe condition?

    • 7 — debugging
    • 0 — emergency
    • 1 — alert
    • 3 — error

    Syslog severity runs 0 (emergencies, most severe) to 7 (debugging, least severe), so a lower number is more urgent.

  6. Which protocol uses UDP ports 161 and 162?

    • SNMP
    • NTP
    • Syslog
    • TFTP

    SNMP agents listen on UDP 161 and traps are sent to UDP 162. Syslog is UDP 514 and TFTP is UDP 69.

  7. Which DSCP value marks voice traffic for expedited forwarding (EF)?

    • 46
    • 0
    • 10
    • 34

    DSCP 46 is EF, the recommended marking for voice. DSCP 0 is best effort, and the class-selector values such as 10 and 34 are lower priorities.

  8. Which ACL type can match source address, destination address, and port numbers?

    • Standard
    • Extended
    • Named standard
    • VLAN ACL

    Extended ACLs match source, destination, protocol, and ports. Standard ACLs match only the source address, whether numbered or named.

  9. Where should a standard ACL be placed?

    • Near the source
    • Near the destination
    • On every router in the path
    • Only on the core router

    Because a standard ACL filters on source alone, placing it near the destination avoids blocking traffic that is merely passing nearby. Extended ACLs go near the source.

  10. Which feature binds a MAC address to a switch port to stop MAC flooding?

    • Port security
    • Dynamic ARP inspection
    • DHCP snooping
    • Root guard

    Port security limits and locks the MAC addresses allowed on a port. DAI protects ARP, DHCP snooping protects DHCP, and root guard protects STP.

  11. Which wireless security protocol uses SAE (Simultaneous Authentication of Equals)?

    • WEP
    • WPA
    • WPA2
    • WPA3

    WPA3 introduces SAE to replace the WPA2 four-way handshake's pre-shared-key weakness. WPA2 uses AES-CCMP; WPA used TKIP; WEP is obsolete.

  12. In REST, which HTTP method maps to the CRUD "create" operation?

    • GET
    • POST
    • PUT
    • DELETE

    POST creates a new resource. GET reads, PUT replaces or updates a known resource, and DELETE removes it — the four CRUD verbs.

Review table

If you missed a question, use this table to find the domain and the lesson to revisit.

QuestionsDomainWhere to revise
1–51.0 Network FundamentalsWeek 1 · OSI lessons; Week 3 · Reference Models
6–101.0 Network FundamentalsWeek 6 · IPv4 Special Addresses; Week 7 · Subnetting
11–161.0 Network FundamentalsWeek 4 · Cabling and Wireless; Week 8 · TCP/UDP
17–242.0 Network AccessWeek 5 · VLAN, Trunking, EtherChannel, STP
25–302.0 Network AccessWeek 5 · CDP/LLDP, Device Management; Week 4 · WLC
31–353.0 IP ConnectivityWeek 3 · Static Routing; Week 6 · Routing Table and Forwarding
36–403.0 IP ConnectivityWeek 6 · OSPFv2 and FHRP
41–443.0 IP ConnectivityWeek 6 · First Hop Redundancy Protocols
45–484.0 IP ServicesWeek 9 · NAT, DHCP, NTP
49–524.0 IP ServicesWeek 9 · Syslog, SNMP, QoS
53–555.0 Security FundamentalsWeek 10 · ACLs, Layer 2 Security, Wireless Security
566.0 Automation and ProgrammabilityWeek 12 · REST APIs and HTTP CRUD

Sources & references

  1. Cisco. CCNA Exam v1.1 (200-301) Exam Topics. learningcontent.cisco.com.
  2. Rekhter, Y. et al. RFC 1918: Address Allocation for Private Internets (1996). rfc-editor.org/rfc/rfc1918.
  3. Moy, J. RFC 2328: OSPF Version 2 (1998). rfc-editor.org/rfc/rfc2328.
  4. Droms, R. RFC 2131: Dynamic Host Configuration Protocol (1997). rfc-editor.org/rfc/rfc2131.
  5. IEEE. IEEE 802.1Q — Bridges and Bridged Networks. standards.ieee.org.

Target exams: CCNA 200-301 v1.1 · CyberOps Associate 200-201. Last content verification: 2026-10-11.