Practice Exam 1
A full-length, four-part practice exam of 56 questions spanning all six CCNA domains. Set a timer for 120 minutes, sit it in one sitting with no notes, then score yourself here. The mix of questions, not the format, is what prepares you: every answer explains the reasoning so a wrong guess becomes a lesson.
How to sit this exam
The real CCNA is a 120-minute exam of about 100 questions, and the pass mark has historically been around 825 out of 1000 (roughly 82%). Cisco does not publish a hard cut-off, so use a practical target: aim for 85% or better here, and treat anything below 80% as a signal to revisit the domain before exam day.
Give yourself the full 120 minutes for these 56 questions — that is generous, which is deliberate. Use the spare time to re-read flagged questions. Mark every question you guessed, even when you answer correctly: a guess that lands is still a gap in knowledge.
Part 1 — Network Fundamentals
Select the single best answer. Feedback and an explanation appear immediately after you choose.
-
Which OSI layer is responsible for logical addressing and path selection between networks?
- Physical
- Data Link
- Network
- Transport
Layer 3 (Network) carries the logical address — an IP address — and routers use it to choose a path. Physical deals with bits, Data Link with frames and MAC addresses, Transport with end-to-end segments.
-
Which device forwards frames based on MAC addresses within a single broadcast domain?
- Router
- Switch
- Firewall
- Modem
A switch learns MAC addresses and forwards frames inside one LAN. A router forwards packets between networks using IP addresses; a firewall filters traffic.
-
A company must connect two different IP subnets so hosts can communicate. Which device is required?
- Switch
- Hub
- Router
- Repeater
Different subnets means Layer 3 forwarding, which is a router's job. Switches, hubs, and repeaters all stay within one subnet.
-
In the TCP/IP model, which layer corresponds to OSI Layers 5, 6, and 7?
- Network Access
- Internet
- Transport
- Application
The TCP/IP Application layer folds together the OSI Session, Presentation, and Application layers. Its Network Access layer merges OSI Data Link and Physical.
-
How many usable host addresses does a /27 subnet provide?
- 30
- 32
- 62
- 126
A /27 leaves 5 host bits: 25 = 32 addresses, minus the network and broadcast = 30 usable hosts.
-
Which of these is a valid RFC 1918 private IPv4 address?
- 172.32.0.1
- 11.0.0.1
- 192.168.10.5
- 169.254.1.1
The private ranges are 10.0.0.0/8, 172.16.0.0/12 (172.16–172.31), and 192.168.0.0/16. 169.254.0.0/16 is APIPA, not RFC 1918.
-
Which IPv6 address type begins with the prefix FE80::/10?
- Global unicast
- Link-local
- Unique local
- Multicast
Link-local addresses are FE80::/10 and are used on a single link. Global unicast is 2000::/3, unique local is FC00::/7, and multicast is FF00::/8.
-
Which is the correct compressed form of 2001:0db8:0000:0000:0000:ff00:0042:8329?
- 2001:db8::ff00:42:8329
- 2001:0db8::ff00:42:8329
- 2001:db8:0:0:0:ff00:42:8329::
- 2001:db8::ff00::42:8329
Leading zeros are dropped (0db8 → db8, 0042 → 42) and the single longest run of zero groups becomes
::, which may appear only once. -
Which cabling type carries a single light path and supports the longest distances?
- Cat 6 UTP
- Multimode fiber
- Single-mode fiber
- Coaxial
Single-mode fiber has a small core and one light path, so it reaches the farthest of any medium taught here. Multimode fiber uses multiple paths and shorter distances; copper is shorter still.
-
One side of a link auto-negotiates 1000 Mbps and the other negotiates 100 Mbps. What is the likely outcome?
- Full-speed 1000 Mbps operation
- A speed mismatch that degrades or breaks the link
- A duplex mismatch only
- No change at all
When speed differs, the link either fails to come up or runs poorly. A duplex mismatch is a separate fault, where both ends agree on speed but not on duplex.
-
What type of address is FF:FF:FF:FF:FF:FF?
- Unicast
- Multicast
- Broadcast
- Anycast
The all-ones MAC address is the Layer 2 broadcast address, received by every device in the broadcast domain.
-
Which transport protocol is connection-oriented and uses a three-way handshake?
- UDP
- ICMP
- TCP
- ARP
TCP opens a connection with SYN, SYN-ACK, ACK and provides reliability. UDP is connectionless; ICMP and ARP are not transport protocols.
-
Which command displays the IP configuration on a Windows host?
- ifconfig
- ipconfig
- ip addr
- netstat
Windows uses
ipconfig. Linux and older macOS useifconfigorip addr; macOS also usesifconfig.netstatshows connections, not addressing. -
Which concept describes delivering both electrical power and data over the same Ethernet cable?
- Power over Ethernet (PoE)
- A VLAN
- Spanning Tree
- NAT
PoE lets a switch power devices such as access points and IP phones, removing the need for a separate power outlet at the device.
-
Which is a valid reason to use private IPv4 addressing?
- To route the addresses directly on the public Internet
- To conserve public addresses and enable NAT
- To avoid subnetting entirely
- To increase link bandwidth
Private addresses can be reused inside every organisation, and NAT translates them to public addresses at the edge. They are not routable on the public Internet.
-
Which statement best describes server virtualization?
- Running multiple logical systems on shared physical hardware
- Physically duplicating every server
- A routing protocol for data centres
- A wireless encryption standard
Virtualization runs several virtual machines or containers on one physical host, sharing CPU, memory, and network adapters. It is not a protocol or a wireless standard.
Part 2 — Network Access
VLANs, trunking, discovery, EtherChannel, STP, and wireless.
-
What is the default native VLAN on an 802.1Q trunk?
- VLAN 100
- VLAN 1
- VLAN 0
- There is no default
VLAN 1 is the default native VLAN, and its traffic crosses a trunk untagged. Best practice is to move it to an unused VLAN, but the default remains VLAN 1.
-
Which command places an interface into VLAN 20 as an access port?
- switchport mode trunk
- switchport access vlan 20
- vlan 20 access
- switchport trunk vlan 20
switchport access vlan 20assigns the port's access VLAN. The other options set trunking, are invalid syntax, or apply to trunk VLANs. -
Which discovery protocol is an open standard and vendor-neutral?
- CDP
- LLDP
- DTP
- VTP
LLDP is IEEE 802.1AB and works between vendors. CDP is Cisco-proprietary; DTP negotiates trunking and VTP propagates VLAN databases.
-
Which STP feature immediately places an access port into the forwarding state?
- PortFast
- UplinkFast
- BackboneFast
- Root guard
PortFast skips the listening and learning delays on a port connected to an end device. UplinkFast and BackboneFast are legacy convergence tools; root guard protects the root role.
-
What is the default bridge priority used by Spanning Tree?
- 4096
- 8192
- 32768
- 65536
The default bridge priority is 32768, and it changes in steps of 4096. The switch with the lowest bridge ID becomes root.
-
Which switch is elected as the STP root bridge?
- The one with the lowest bridge ID
- The one with the highest bridge ID
- The one with the lowest MAC address only
- The one with the highest port number
The lowest bridge ID wins. The bridge ID combines priority and MAC, so a low priority beats a lower MAC unless the priorities are equal.
-
Which pair of keywords is used for LACP EtherChannel negotiation?
- on / off
- active / passive
- desirable / auto
- trunk / access
LACP uses
activeandpassive. Desirable/auto belongs to PAgP, and on/off bypasses negotiation entirely. -
Which command configures an EtherChannel to a router using LACP?
- channel-group 1 mode active
- channel-group 1 mode desirable
- channel-group 1 mode on
- channel-group 1 mode auto
A router supports LACP, which uses
mode active. Desirable and auto are PAgP, and on forces the bundle without negotiation. -
What is the purpose of the native VLAN on an 802.1Q trunk?
- To tag every frame crossing the trunk
- To carry untagged traffic across the trunk
- To block STP BPDUs
- To route between VLANs
The native VLAN carries frames that are not tagged with an 802.1Q header. If the two ends disagree, a native VLAN mismatch results, and traffic can leak between VLANs.
-
Which feature prevents a rogue switch from becoming the STP root?
- BPDU guard
- Root guard
- Port security
- Dynamic ARP inspection
Root guard stops a superior BPDU on a designated port, keeping the current root. BPDU guard shuts a PortFast port that receives any BPDU.
-
Which discovery protocol is Cisco-proprietary?
- LLDP
- CDP
- STP
- VTP
CDP (Cisco Discovery Protocol) is proprietary. LLDP is the open standard, and STP and VTP are not discovery protocols.
-
In a controller-based wireless network, which AP mode tunnels client traffic back to the WLC by default?
- FlexConnect
- Local
- Sniffer
- Bridge
In local mode the AP builds a CAPWAP tunnel to the WLC and client traffic is centralised there. FlexConnect can switch traffic locally; sniffer and bridge are specialised modes.
-
When an IP phone is attached to a switch port, which VLAN arrangement is typical?
- One VLAN only
- A data VLAN plus a voice VLAN on the same port
- A trunk with no access VLAN
- The native VLAN only
The port carries both a data VLAN for the attached PC and a voice VLAN for the phone, tagged with 802.1Q so the phone can separate the two.
-
Which remote management method encrypts the session?
- Telnet
- HTTP
- SSH
- FTP
SSH encrypts the management session. Telnet and HTTP send credentials in clear text, and FTP transfers files without encryption.
Part 3 — IP Connectivity
Routing tables, forwarding decisions, static routing, OSPFv2, and first hop redundancy.
-
What is the administrative distance of OSPF?
- 90
- 100
- 110
- 120
OSPF is 110. EIGRP is 90, RIP is 120, static is 1, and connected is 0. Lower administrative distance is preferred.
-
A router learns the same prefix from a static route and from OSPF. Which route enters the routing table?
- The OSPF route
- The static route
- Both, by load-balancing
- Neither
Administrative distance decides first: static is 1 and OSPF is 110, so the static route wins. Equal-cost load-balancing only happens within the same protocol and metric.
-
A router has both 10.1.0.0/16 and 10.1.1.0/24 in its table and must forward a packet to 10.1.1.5. Which route does it use?
- The /16 route
- The /24 route
- Both, in parallel
- Neither
Longest prefix match wins: the /24 is more specific than the /16, so it is preferred for 10.1.1.5 regardless of administrative distance.
-
Which command creates a default route out through 192.168.1.1?
- ip route 0.0.0.0 0.0.0.0 192.168.1.1
- ip default-gateway 192.168.1.1
- ip route 192.168.1.1 255.255.255.255
- route add default 192.168.1.1
ip route 0.0.0.0 0.0.0.0 192.168.1.1is the default route.ip default-gatewayis for a host-mode device without routing enabled, and the others are invalid or single-host routes. -
A floating static route is configured with which characteristic?
- A higher administrative distance
- A lower metric
- A different routing protocol
- No next hop
A floating static is a backup: a deliberately high administrative distance keeps it out of the table until the primary route fails.
-
Which OSPF packet discovers and maintains neighbour relationships?
- LSA
- Hello
- Database Description (DBD)
- Link State Update (LSU)
Hello packets form and maintain adjacencies, carrying the router ID and parameters. DBD and LSU exchange and flood database information.
-
On a broadcast OSPF network, which multicast address do all OSPF routers listen on?
- 224.0.0.5
- 224.0.0.6
- 224.0.0.9
- 224.0.0.10
224.0.0.5 is AllSPFRouters. 224.0.0.6 is AllDRouters, used by the DR and BDR. 224.0.0.9 and 224.0.0.10 belong to RIPv2 and EIGRP.
-
On a broadcast OSPF network, which devices receive updates sent to 224.0.0.6?
- All routers
- Only the DR and BDR
- Only the DR
- Only the ABR
224.0.0.6 is AllDRouters: only the designated and backup designated routers listen. All other routers use 224.0.0.5.
-
If no router ID is configured, how does OSPF choose one?
- Highest loopback address, else highest physical interface IP
- Lowest loopback address, else lowest physical IP
- The interface MAC address
- The device hostname
OSPF prefers the highest loopback address; without a loopback it uses the highest IP of an active physical interface. An explicit
router-idalways overrides both. -
Which protocol is a first hop redundancy protocol?
- OSPF
- HSRP
- LACP
- DTP
HSRP is a Cisco first hop redundancy protocol that gives hosts a stable virtual gateway. OSPF is a routing protocol; LACP bundles links; DTP negotiates trunking.
-
What is the default HSRP priority?
- 1
- 100
- 110
- 255
HSRP defaults to priority 100, with a higher value winning. VRRP also defaults to 100.
-
In HSRP, which router becomes the active gateway?
- Highest priority, then highest IP address
- Lowest priority
- Highest MAC address
- Chosen at random
The highest priority wins; ties are broken by the highest interface IP address. Preemption is off by default unless configured.
-
Which MAC address does HSRP use for its virtual gateway?
- 0000.0C07.ACxx
- 0000.5E00.01xx
- FFFF.FFFF.FFFF
- 0180.C200.0000
HSRP v1 uses 0000.0C07.ACxx, where xx is the group number. 0000.5E00.01xx is VRRP's virtual MAC.
-
Which metric does OSPF use by default?
- Hop count
- Cost
- Bandwidth in kbps
- Delay
OSPF cost is derived from interface bandwidth: 108 divided by bandwidth in bits per second at the default reference. Hop count is RIP's metric.
Part 4 — IP Services, Security & Automation
NAT, DHCP, NTP, syslog, SNMP, QoS, ACLs, Layer 2 security, wireless security, and automation.
-
Which NAT type lets many inside hosts share one public address using unique source ports?
- Static NAT
- Dynamic NAT
- PAT (overload)
- NAT64
PAT, also called NAT overload, tracks inside hosts by source port so one public address serves many sessions. Dynamic NAT uses a pool of public addresses.
-
Which command enables PAT using an ACL on an interface?
- ip nat inside source list 1 interface g0/0 overload
- ip nat inside source static
- ip nat pool
- ip nat destination
The
overloadkeyword turns the translation into PAT.staticis one-to-one, and a pool creates dynamic NAT without port overloading. -
Which transport protocol and port does NTP use?
- TCP 123
- UDP 123
- UDP 69
- TCP 49
NTP uses UDP 123. UDP 69 is TFTP and TCP 49 is TACACS+.
-
In DORA, which DHCP message does a client send first?
- Offer
- Request
- Discover
- Acknowledge
DORA is Discover, Offer, Request, Acknowledge. The client begins with a broadcast Discover; the server replies with an Offer.
-
Which syslog severity level represents the most severe condition?
- 7 — debugging
- 0 — emergency
- 1 — alert
- 3 — error
Syslog severity runs 0 (emergencies, most severe) to 7 (debugging, least severe), so a lower number is more urgent.
-
Which protocol uses UDP ports 161 and 162?
- SNMP
- NTP
- Syslog
- TFTP
SNMP agents listen on UDP 161 and traps are sent to UDP 162. Syslog is UDP 514 and TFTP is UDP 69.
-
Which DSCP value marks voice traffic for expedited forwarding (EF)?
- 46
- 0
- 10
- 34
DSCP 46 is EF, the recommended marking for voice. DSCP 0 is best effort, and the class-selector values such as 10 and 34 are lower priorities.
-
Which ACL type can match source address, destination address, and port numbers?
- Standard
- Extended
- Named standard
- VLAN ACL
Extended ACLs match source, destination, protocol, and ports. Standard ACLs match only the source address, whether numbered or named.
-
Where should a standard ACL be placed?
- Near the source
- Near the destination
- On every router in the path
- Only on the core router
Because a standard ACL filters on source alone, placing it near the destination avoids blocking traffic that is merely passing nearby. Extended ACLs go near the source.
-
Which feature binds a MAC address to a switch port to stop MAC flooding?
- Port security
- Dynamic ARP inspection
- DHCP snooping
- Root guard
Port security limits and locks the MAC addresses allowed on a port. DAI protects ARP, DHCP snooping protects DHCP, and root guard protects STP.
-
Which wireless security protocol uses SAE (Simultaneous Authentication of Equals)?
- WEP
- WPA
- WPA2
- WPA3
WPA3 introduces SAE to replace the WPA2 four-way handshake's pre-shared-key weakness. WPA2 uses AES-CCMP; WPA used TKIP; WEP is obsolete.
-
In REST, which HTTP method maps to the CRUD "create" operation?
- GET
- POST
- PUT
- DELETE
POST creates a new resource. GET reads, PUT replaces or updates a known resource, and DELETE removes it — the four CRUD verbs.
Review table
If you missed a question, use this table to find the domain and the lesson to revisit.
| Questions | Domain | Where to revise |
|---|---|---|
| 1–5 | 1.0 Network Fundamentals | Week 1 · OSI lessons; Week 3 · Reference Models |
| 6–10 | 1.0 Network Fundamentals | Week 6 · IPv4 Special Addresses; Week 7 · Subnetting |
| 11–16 | 1.0 Network Fundamentals | Week 4 · Cabling and Wireless; Week 8 · TCP/UDP |
| 17–24 | 2.0 Network Access | Week 5 · VLAN, Trunking, EtherChannel, STP |
| 25–30 | 2.0 Network Access | Week 5 · CDP/LLDP, Device Management; Week 4 · WLC |
| 31–35 | 3.0 IP Connectivity | Week 3 · Static Routing; Week 6 · Routing Table and Forwarding |
| 36–40 | 3.0 IP Connectivity | Week 6 · OSPFv2 and FHRP |
| 41–44 | 3.0 IP Connectivity | Week 6 · First Hop Redundancy Protocols |
| 45–48 | 4.0 IP Services | Week 9 · NAT, DHCP, NTP |
| 49–52 | 4.0 IP Services | Week 9 · Syslog, SNMP, QoS |
| 53–55 | 5.0 Security Fundamentals | Week 10 · ACLs, Layer 2 Security, Wireless Security |
| 56 | 6.0 Automation and Programmability | Week 12 · REST APIs and HTTP CRUD |
Sources & references
- Cisco. CCNA Exam v1.1 (200-301) Exam Topics. learningcontent.cisco.com.
- Rekhter, Y. et al. RFC 1918: Address Allocation for Private Internets (1996). rfc-editor.org/rfc/rfc1918.
- Moy, J. RFC 2328: OSPF Version 2 (1998). rfc-editor.org/rfc/rfc2328.
- Droms, R. RFC 2131: Dynamic Host Configuration Protocol (1997). rfc-editor.org/rfc/rfc2131.
- IEEE. IEEE 802.1Q — Bridges and Bridged Networks. standards.ieee.org.
Target exams: CCNA 200-301 v1.1 · CyberOps Associate 200-201. Last content verification: 2026-10-11.