Week 4 · Lesson 2

Bandwidth, Signal Encoding & Network Interface Considerations

How fast can this link go? What does “1 Gbps” actually measure? And how do voltages on a wire carry ones and zeros without the receiver losing the beat? This lesson gives the exact vocabulary — bandwidth, throughput, latency, goodput, encoding, baud, duplex — and shows how a NIC turns frames into signals.

CCNA 200-301 Domain 1.6 Physical Interfaces & Cabling Verified 2026-10-11
Part 1

Bandwidth, throughput, latency, goodput

These four words are used loosely in daily speech but mean precise things in networking.

Definition — the four measures. Bandwidth is the theoretical capacity of a link — the maximum number of bits it can carry per second. Throughput is the rate actually achieved. Latency is the time a bit takes to travel from source to destination. Goodput is the throughput of useful payload after overhead and retransmissions are removed.
TermMeaningUnits
BandwidthMaximum capacity of the link.bits per second (bps)
ThroughputThe rate actually achieved in practice.bits per second (bps)
LatencyDelay for a bit to reach the destination (propagation, processing, queuing).milliseconds (ms)
GoodputUseful application-payload rate after headers and retransmits.bits per second (bps)

Throughput is almost always lower than bandwidth. A 1 Gbps link might deliver 940 Mbps of throughput because the Ethernet preamble, inter-frame gap and headers consume capacity; a busy network can drop lower still due to congestion and retransmissions. Latency is not a rate at all — it is a time. A link can have high bandwidth and still feel slow if its latency is high (a classic problem on satellite links).

Exam tip. If a question gives a link rated 1 Gbps but says the transfer ran at 700 Mbps, that is throughput, not bandwidth. “Bandwidth” is the rated capacity; anything measured live is throughput.
Capacity vs what you actually get · select a scenario
goodput
Bandwidth 1000 Mbps Throughput 0 Mbps Goodput 0 Mbps Latency 0 ms

Part 2

Units: bps and the b-versus-B trap

Network speed is measured in bits per second (bps), and the prefixes step by factors of 1000.

UnitRepresentsExample
b/s (bps)bits per seconda dial-up modem: 56 kbps
kbps1 000 bpsDSL upload
Mbps1 000 000 bpsFast Ethernet: 100 Mbps
Gbps1 000 000 000 bpsGigabit Ethernet: 1 Gbps

The single most common mistake is confusing b (bit) with B (byte). There are 8 bits in one byte, so a 100 Mbps link transfers only about 12.5 MB/s (100 ÷ 8). A storage spec quoted in MB (megabytes) uses a different unit and a different meaning from a network spec quoted in Mb (megabits).

Watch out. Mb = megabit (network speed, decimal ×1000). MB = megabyte (file size, often binary ×1024). When you estimate transfer time, convert to the same unit first: time = size ÷ rate, then fix the units.
Bits per second to bytes per second · move the slider
12.5MB/s at best — and a 1 GB file takes 80 seconds

Part 3

Signalling: bits into signals

The physical layer carries bits by varying a physical property of the medium. On copper it varies the voltage; on fibre the intensity or wavelength of light; in wireless the power, frequency or phase of radio waves. The sender and receiver must agree on which variation means one and which means zero — that agreement is the signalling method.

Some media encode the signal directly onto the medium (baseband), as Ethernet does. Others modulate a higher-frequency carrier wave, which is how a single phone line carries both voice and ADSL data at once.

Encoding and the NRZ example

Encoding is the rule that maps a group of bits to a pattern of signal elements. The simplest rule is NRZ (non-return to zero): transmit the high level for a 1 and the low level for a 0, changing only when the bit changes. Below, the bits 1 0 1 1 0 are drawn both ways — switch schemes to compare them.

NRZ vs Manchester · select an encoding
high (+V) low (−V) time → 1 0 1 1 0

As Lesson 1 introduced, any encoding must define four things, and NRZ illustrates all of them:

  1. Voltage level / change. NRZ uses a level (high or low), not a transition.
  2. Bit timing. Each level is held for exactly one bit interval; the receiver samples mid-interval.
  3. Mode. NRZ here is a baseband, two-level scheme on the wire.
  4. Purpose. NRZ is simple and efficient, but it does not guarantee transitions, so it needs help (block coding such as 4B/5B) to keep the clocks synchronised.
Part 4

Baud versus bits per second

A symbol is one signal element. The number of symbols sent per second is the baud rate (also called the signalling rate). The number of bits sent per second is the bit rate. When each symbol carries exactly one bit the two are equal — but with multi-level encoding a symbol can carry several bits at once.

Key relationship. bps = baud × bits per symbol. Equivalently, baud = bps ÷ bits per symbol.
Levels (symbols)Bits per symbolIf baud = 1 000
2 (binary)11 000 bps
422 000 bps
833 000 bps
1644 000 bps

Worked example: Gigabit Ethernet's 1000BASE-T uses PAM-5 (five voltage levels) across four pairs. It runs at 125 MBd per pair and encodes 2 bits per symbol per pair, giving 250 Mbps per pair. Multiply by four pairs and you reach 1 Gbps. This is why bit rate and baud rate are not the same number.

Exam tip. “Baud” is never the same as “bits per second” unless each symbol carries one bit. A question that says a line uses 4 signal levels is telling you each symbol = 2 bits, so the bit rate is twice the baud rate.
bps = baud × bits per symbol · try it
4 000bits per second

Part 5

Half duplex versus full duplex

Duplex describes whether a device can send and receive at the same time on the medium.

ModeBehaviourConsequence
SimplexOne direction only.e.g. a legacy broadcast link
Half duplexBoth directions, but not at once.Collisions possible; needs CSMA/CD
Full duplexBoth directions at the same time.No collisions; doubles usable capacity

Modern switched Ethernet is full duplex: each device has its own transmit and receive path (separate wire pairs in twisted-pair cable), so collisions cannot occur and CSMA/CD is disabled. A duplex mismatch — one end half, the other full — is a classic cause of a slow, erroring link.

Note. On a twisted-pair Ethernet link, 1000BASE-T requires full duplex and autonegotiation. If autonegotiation fails, a duplex mismatch can result, so allowing both ends to negotiate (rather than hard-setting one side) is best practice.
Part 6

The NIC and its interfaces

The network interface card (NIC) is the hardware that connects a host to the network. It implements two layers: the physical layer (turning bits into signals, handling speed and duplex) and the data link layer (building Ethernet frames and holding the device's MAC address, burned into the card).

A NIC has a rated interface speed (for example 10/100/1000 Mbps). The interface the host actually uses is determined by the port on the switch and the cable between them.

Speed autonegotiation

Autonegotiation lets two connected Ethernet devices advertise the speeds and duplex modes they support, then automatically pick the best common setting. A port that supports 10/100/1000 Mbps and negotiates with a 100 Mbps partner settles on 100 Mbps full duplex.

The rule to remember: the link always runs at the highest speed and duplex both ends support. If negotiation fails, some devices fall back to speed sensing, which can leave a duplex mismatch — a subtle fault that slows the link and inflates errors without taking it down.

Key terms. Bandwidth — theoretical maximum capacity in bits per second. Throughput — the rate actually achieved. Latency — the time for a bit to travel. Goodput — useful payload after overhead and retransmissions. NRZ — 1 = high level, 0 = low level. Baud rate — symbols per second. Full duplex — simultaneous two-way transmission with no collisions. Autonegotiation — automatic selection of the best common speed and duplex.
Part 7 · Your turn

Review

Check what you have learned with these review questions.

Review · 6 questions

Sources

Sources & references

  1. IEEE. IEEE 802.3 — defines Ethernet PHYs, encoding (PAM-5 for 1000BASE-T) and full-duplex operation. standards.ieee.org/ieee/802.3.
  2. TIA. ANSI/TIA-568.2-D — cabling categories, bandwidth (MHz) and the 100 m channel. tiaonline.org.
  3. Cisco. CCNA (200-301) Exam Topics, Domain 1.6 (physical interfaces and cabling). cisco.com.
  4. Peterson, L. & Davie, B. Computer Networks: A Systems Approach, Section 2.2 (Encoding). book.systemsapproach.org.

Target exams: CCNA 200-301 v1.1 · CyberOps Associate 200-201. Last content verification: 2026-10-11.